R/PUDUCHERRY SOR 2024-25
Aluminium Work rates
41 aluminium work items from the Puducherry PWD, effective 2024-08-14.
- Items
- 41
- Lowest rate
- ₹7.11
- Highest rate
- ₹5,431.72
- Effective from
- 2024-08-14
S-01/RATE ITEMS41 ITEMS
Aluminium Work rates in the Puducherry Puducherry Schedule of Rates 2024-25 run from ₹7.11 to ₹5,431.72. Transcribed from Puducherry PWD — Puducherry Schedule of Rates 2024-25, Puducherry region. Base PDF only; PWD has since issued Correction Slip-3 (22 January 2025) for all four regions, so some rates here may be superseded.. For reference only: verify against the official source before pricing a bid.
/
Unit
41 items. Scroll the table to browse
| Description | Unit | ||
|---|---|---|---|
| 21.1.1.1 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the direction.(Glazing, paneling and dash fasteners to be paid for separately) - for fixed portion - anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15) | KG | 684.91 |
| 21.1.1.2 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the direction.(Glazing, paneling and dash fasteners to be paid for separately) - for fixed portion - Powder coated aluminium (minimum thickness of powder coating 50 micron) | KG | 692.38 |
| 21.1.1.3 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the direction. (Glazing, paneling and dash fasteners to be paid for separately) - for fixed portion - Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) | KG | 699.85 |
| 21.1.2.1 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the direction.(Glazing, paneling and dash fasteners to be paid for separately) - for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately) - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC15) | KG | 795.38 |
| 21.1.2.2 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the direction.(Glazing, paneling and dash fasteners to be paid for separately) - for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately) - Powder coated aluminium (minimum thickness of powder coating 50 micron) | KG | 802.85 |
| 21.1.2.3 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the direction.(Glazing, paneling and dash fasteners to be paid for separately) - for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately) - Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) | KG | 810.32 |
| 21.2.1 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 grade I type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and the direction.- Pre - laminated particle board with decorative lamination on one side and balancing lamination on other side | Sqm | 1,022.81 |
| 21.2.2 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 grade I type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and the direction.- Pre - laminated particle board with decorative lamination on both sides | Sqm | 1,060.15 |
| 21.3.1 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the direction. (cost of aluminium snap beading shall be paid in basic item) - with float glass panes of 4.0 mm thickness | Sqm | 1,448.60 |
| 21.3.2 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the direction.(cost of aluminium snap beading shall be paid in basic item) - with float glass panes of 5 mm thickness | Sqm | 1,667.68 |
| 21.3.3 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the direction.(cost of aluminium snap beading shall be paid in basic item) - with float glass panes of 8 mm thickness (weight not less than 20kg / sqm) | Sqm | 2,340.58 |
| 21.4.1 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS:6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete and the direction.- with stainless steel cover plate minimum 1.25mm thickness | Each | 3,659.33 |
| 21.4.2 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS:6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete and the direction.- with brass cover plate minimum 1.25mm thickness | Each | 2,667.75 |
| 21.5 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee / angle sections, of approved make conforming to IS:733 in frames of false ceiling including aluminium angle cleats with necessary C.P.brass / stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450mm centre to centre and fixing the frame work to G.I.level adjusting hangers 6mm dia with necessary cadmium plated machine screws all complete as per approved architectural drawings and the direction.(level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately | KG | 938.21 |
| 21.6 | Providing and fixing 6mm dia G.I.level adjusting hangers (upto 1200 mm length),fixed to roof slabs by means of ceiling cleats made out of G.I.flat 40x3 mm size 60 mm long and stainless steel expandable dash fastener of 12.5mm dia and 50 mm long, complete as per direction of Engineer-in-charge | Each | 201.16 |
| 21.7.1 | Providing and fixing machine moulded aluminium covering of approved pattern and design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces / ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fastners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick 15mm dia, at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge - Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) | KG | 732.84 |
| 21.7.2 | Providing and fixing machine moulded aluminium covering of approved pattern and design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces / ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fastners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick 15mm dia, at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge - Powder coated aluminium sheet 2.5mm thick (minimum thickness of powder coating 50 micron) | KG | 740.31 |
| 21.8.1 | Filling the gap in between aluminium frame & adjacent RCC / Brick / Stone work by providing weather silicon sealent over backer rod of approved quality as per architectural drawings and direction complete - Upto 5 mm depth and 5 mm width | Metre | 82.63 |
| 21.9.1 | Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruted sections - for fixed portion | KG | 7.11 |
| 21.9.2 | Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruted sections - for shutters of doors, windows, & ventilators | KG | 7.11 |
| 21.10 | Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (both primary and secondary sealant) etc. as per specifications, drawings and direction complete | Sqm | 3,916.17 |
| 21.11.1 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete - 205x19 mm | Each | 245.97 |
| 21.11.2 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete - 255x19 mm | Each | 267.31 |
| 21.11.3 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete -355 x 19 mm | Each | 309.99 |
| 21.11.4 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete - 510 x 19 mm | Each | 601.63 |
| 21.11.5 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete -710x19mm | Each | 1,065.41 |
| 21.12.1 | Providing and fixing aluminium tubular handle bar 32 mm outer dia 3.0 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-charge - Anodized (AC 15) aluminium tubular handle bar | Each | 881.98 |
| 21.12.2 | Providing and fixing aluminium tubular handle bar 32 mm outer dia 3.0 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-charge - Powder coated minimum thickness 50 micron aluminium tubular handle bar | Each | 893.61 |
| 21.12.3 | Providing and fixing aluminium tubular handle bar 32 mm outer dia 3.0 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-charge - Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar | Each | 905.23 |
| 21.13 | Providing and fixing brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete | Each | 1,242.13 |
| 21.14 | Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS:733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid separately) | KG | 594.28 |
| 21.15.1 | Providing and fixing aluminium casement windows fastener of required lenghth for aluminium windows with necessary screws etc.complete - anodized (AC 15) aluminium | Each | 76.34 |
| 21.15.2 | Providing and fixing aluminium casement windows fastener of required lenghth for aluminium windows with necessary screws etc.complete - Powder coated minimum thickness 50 micron aluminium | Each | 63.54 |
| 21.15.3 | Providing and fixing aluminium casement windows fastener of required lenghth for aluminium windows with necessary screws etc.complete - Polyster powder coated minimum thickness 50 micron aluminium | Each | 69.23 |
| 21.16.1 | Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc.complete as per direction of Engineer-in-charge - Anodized (AC 15) aluminium | Each | 63.54 |
| 21.16.2 | Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc.complete as per direction of Engineer-in-charge - Powder coated minimum thickness 50 micron aluminium | Each | 66.38 |
| 21.16.3 | Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc.complete as per direction of Engineer-in-charge - Polyster powder coated minimum thickness 50 micron aluminium | Each | 70.65 |
| 21.17 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design / pattern, with approved standard section and fixed to the existing window frame with C.P.brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction - (Only weight of grill to be measured for payment) | KG | 607.36 |
| 21.18 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately) | Sqm | 5,431.72 |
| 21.19.1 | Filling the gap in between aluminium / stone / wood frame and adjacent RCC / Brick / Stone / Wood / Ceramic / Gypsum work by providing weather / structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction complete, complying to ASTM C920, DIN 18540-F & ISO 11600 - upto 5mm depth and 5mm width | Metre | 144.54 |
| 21.19.2 | Filling the gap in between aluminium / stone / wood frame and adjacent RCC / Brick / Stone / Wood / Ceramic / Gypsum work by providing weather / structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction complete, complying to ASTM C920, DIN 18540-F & ISO 11600 - upto 10mm depth and 10 mm width | Metre | 197.39 |
S-02/SOURCE RECORD2024-25
- ISSUED BY
- Puducherry PWD
- EFFECTIVE
- 2024-08-14From the Puducherry PWD website, which lists this schedule as "PSR 2024-25 (with effect from 14th August 2024 onwards)". The PDF itself prints no date anywhere in its 1,216 pages.
- RETRIEVED
- 2026-07-29
S-03/CHAPTERS44 MORE
Other chapters in this schedule
- Earth Work70
- Concrete Work72
- Reinforced Concrete Work131
- Brick Work57
- Stone Work50
- Cladding Work71
- Wood and PVC Work493
- Steel Work52
- Flooring91
- Roofing135
- Finishing114
- Repairs To Buildings108
SHOW ALL 44 CHAPTERS
- Dismantling And Demolishing85
- Miscellaneous Building Work25
- Sanitary Installations226
- Water Supply708
- Drainage135
- Pile Work31
- Water Proofing27
- Rain Water Harvesting & TubeWells37
- Conservation of Heritage Buildings7
- Structural Glazing Aluminium Composite Panel5
- New Technologies and Materials196
- Irrigation50
- Water Supply (Public Health)1012
- Sewerage (Public Health)213
- Miscellaneous (Public Health)71
- OHT (Works)8
- Subsoil Exploration7
- Energy Conservation Building Code137
- Site Clearance and Dismantling44
- Earth Work, Erosion Control and Drainages40
- Granular Sub-base63
- Base & Bituminous Construction26
- Traffic Signs,Markings & Other Road Appurtenances41
- Pipe Culverts5
- Maintenance of Roads13
- Horticulture25
- Foundation106
- Substructure54
- Superstructure97
- River Training and Protection Works10
- Repair and Rehabilitation12
- PMGSY -Works25
ARCHED / ESTIMATING
Pricing aluminium work against a live tender
Mapping a tender BOQ to the right schedule items, applying the current cost index and catching where rates have moved since the base edition takes time and is easy to get wrong. We can do it for you: send the tender and we return a priced BOQ on the applicable schedule, with rate build-ups and an engineer's sign-off.