Andhra Pradesh SOR 2026-27
Doors, Shutters & Frames rates
113 doors, shutters & frames items from the Board of Chief Engineers, Government of Andhra Pradesh, effective 2026-06-01.
Doors, Shutters & Frames rates in the Andhra Pradesh Common Schedule of Rates — Part-III (Buildings, Water Supply & Electrical) 2026-27 run from ₹255.00 to ₹26,150.00. Transcribed from Government of Andhra Pradesh — Common Schedule of Rates 2026-27, Part-III (Buildings), Board of Chief Engineers. Reference only — verify against the official source before pricing a bid.
/
113 items — scroll the table to browse
| Description | Unit | ||
|---|---|---|---|
| BMT-N.01 | Providing and fixing factory made polyvinyl chloride (PVC) Door Frame of the size 50 x 47mm with a wall thickness of 5mm, made out of extruded 10 mm rigid PVC foam sheet, mitre cut at two corners and joined with 2nos. of 150mm long brackets of 15x15mm M.S. square tube. The two vertical door profiles are to be reinforced with 19x19mm M.S. Square tube of 19 gauge. The door frame shall be fixed to the wall using 65/100mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 4nos. of screws to be provided for each vertical member & minimum 2nos. for horizontal member etc. complete as per | Rm | 453.00 |
| BMT-N.02 | Providing and fixing 30mm thick Solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 | Sqm | 2,290.00 |
| BMT-N.03 | Providing and fixing 30mm thick BRAND FACTORY MADE BOTHSIDE PRELAM SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of MS. Tubes of 19gauge thickness and size of 19mmX19mm for stiles, top and bottom rails. MS. Frame shall have a coat of steel primers of approved make and manufacture. MS. Frame covered with 5mm thick heat moulded Prelam Pac ‘C’ channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 450 angle on either side forming stiles; and 5mm thick, 95mm wide Prelam Pac sheet out of which 75mm shall be flat and 20mm shall be tapered in 450 on the inner side to form top and bottom rail 115mm wide Prelam Pac sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rail shall be provided either side of the panel. 10mm (5mmX2) thick, 20mmwide cross Pac sheet shall be provided as gap insert for top and bottom rail. Panelling of 5mm thick both side Prelam Pac sheet to be fitted in the MS. Frame welded/ sealed to the stiles | Sqm | 3,190.00 |
| BMT-N.04 | Providing and fixing 30mm thick BRAND FACTORY MADE SOLID SINGLE SIDE PRELAM PANEL PVC DOOR SHUTTER consisting of frame made out of MS. Tubes of 19gauge thickness and size of 19mmX19mm for stiles, and 15mmX15mm for top and bottom rails. The MS. Frame shall have a coat of steel primers of approved make and manufacture. MS. Frame covered with 5mm thick heat moulded single side Prelam Pac ‘C’ channel of size 30mmX50mm to form stiles.5mm thick& 75mm wide single side prelim Pac sheets shall be for the top, bottom and lock rails. Panelling of 5mm thick one side Pac sheet to be fitted in the MS. Frame and sealed to the front (prelam side) stiles and rails (which should have a 5mm 45 bent portion as beading) and attached to the back(white/ivory) stiles and rails which should have a 10mm 900 bent portion as beading ) using 2nos. 15mm wide X 5mm thick Pac sheet beading inside the 90 bent beading. All stiles, rails and beadings are to be joined to the panel using solvent cement etc. an additional 5mm thick Pac strip of 20mm width to be stuck on the interior side of the ‘C” channel using Pac solvent cement adhesive and 10mm(5mmX2) thick, 20mm wide cross Pac sheet to be fitted as gap insert for top and bottom rail etc. complete as per direction of Engineer – inCharge, manufacture specification and drawing | Sqm | 2,364.00 |
| BMT-N.05 | SINGLE SIDE PRELAM SOLID PANEL PVC DOOR FRAME (CHOUKHAT): Providing and fixing factory made Pac single side Prelam door frame of the size 50X47 mm with a wall thickness of 5mm, made out of extruded 5mm rigid Pac single side prelam sheet, meter cut at two corners and joined with 2nos. of 150mm long brackets of 1515mm MS.Square tube. The two vertical door profiles are to be reinforced with 19X19mm MS. square tube of 19guage. The door frame shall be fixed to the wall using 65/100mm long MS. Screws through the frame by using Pac fasteners. a minimum of 4nos. of screws to be provided for each vertical member and minimum 2nos. for horizontal member etc. complete as per manufacture specification and direction of Engineer-in-Charge | Rm | 476.00 |
| BMT-N.06 | Providing and fixing 35mm thick BRAND FACTORY MADE MOULDED DOOR SHUTTER consisting of sold core single leaf flush door of 30mm thickness, lipped with 15mm (5mmX3) thick X 30mm width on one stiles and top rails and 10mm (5mmX2) thick X 30mm width on the other stiles and bottom rails. The inner panel laminated with 2mm thick termite proof, water proof and fire resistant moulded Pac sheet with 2,4,6 raised panel design in different panel and / or prelam colours on one side after routing the moulded design on flush door and 2mm prelam Pac sheet on other side using rubber adhesive on flush door and solvent cement adhesive on Pac lipping etc. complete as per direction of Engineer inCharge, manufacture specification and drawing | Sqm | 3,255.00 |
| BMT-N.07 | MOULDED PVC DOOR WOOD FREE Providing and fixing 30mm thick Brand factory made Moulded door shutter wood free consisting of frame made out of MS. tubes 19gauge thickness and size of 25mmX25mm for stiles, top and bottom rails. MS. Frame shall have a | Sqm | 2,830.00 |
| BMT-N.08 | Providing and fixing 30mm thick BRAND FACTORY MADE WIRE MESH SOLID PVC DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mmX19mm for stiles and 15mm for top, lock & bottom rails. MS. Frame shall have a coat of steel primers of approved make and manufacture. 19mmX19mm M.S. square tubes shall be covered with 5mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 90mm width out of which 75mm shall be flat and 15mm shall be flat and 15mm shall be bent in 900 on the inner side to from top and bottom rail land 130mm wide PVC sheet out of which 100mm shall be flat and 154mm shall be bent in 900 on both side to from lock rail, 10mm(5mmX2) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail. Panel will be of G.I.wire mesh of 24gauge to be fitted in by ’C’ channel of size 35mm X10mm on the either side in the stiles. The inner side ‘C’ channel is fixed by 19mmX19mm MS. Tube on both sides with screws. The wire mesh in top bottom & lock rail is sealed with15mm X 15mm tube with G.I.wire 10mm(5mmX2) thick PVC strip of 25mm width is to be stuck& nails on | Sqm | 2,323.00 |
| BMT-N.09 | Providing and fixing PVC door cladding to the flush doors shutters. For the new doors it shall be pasted with Fevicol SSR 998 or nailed to the old doors. complete as per direction of Engineer – in – charge, manufacturers specification and drawing 1 mm thick | Sqm | 389.00 |
| BMT-N.10 | Providing and fixing PVC door cladding to the flush doors shutters . For the new doors it shall be pasted with Fevicol SSR 998 or nailed to the old doors. complete as per direction of Engineer – in – charge, manufacturers specification and drawing 1.5 mm thick | Sqm | 449.00 |
| BMT-N.11 | Providing and fixing PVC door cladding to the flush doors shutters . For the new doors it shall be pasted with Fevicol SSR 998 or nailed to the old doors. complete as per direction of Engineer – in – charge, manufacturers specification and drawing 2.0 mm thick | Sqm | 519.00 |
| BMT-N.12 | Flush door shutters, solid bond wood block board type with teak ply on both faces.: 25 mm thick conforming to IS:2202 | Sqm | 2,260.00 |
| BMT-N.13 | Flush door shutters, solid bond wood block board type with teak ply on both faces.: 30 mm thick conforming to IS:2202 | Sqm | 2,342.00 |
| BMT-N.14 | Flush door shutters, solid bond wood block board type with teak ply on both faces.: 35 mmthick conforming to IS:2202 | Sqm | 2,517.00 |
| BMT-N.15 | Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 25 mmthick conforming to IS:2202 | Sqm | 1,244.00 |
| BMT-N.16 | Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 30 mmthick conforming to IS:2202 | Sqm | 1,300.00 |
| BMT-N.17 | Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 35 mmthick conforming to IS:2202 | Sqm | 1,580.00 |
| BMT-N.18 | Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 40 mmthick conforming to IS:2202 | Sqm | 1,775.00 |
| BMT-N.19 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 20 mmthick conforming to IS:2202 | Sqm | 1,860.00 |
| BMT-N.20 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 25 mmthick conforming to IS:2202 | Sqm | 2,000.00 |
| BMT-N.21 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 30 mmthick conforming to IS:2202 | Sqm | 1,920.00 |
| BMT-N.22 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 35 mmthick conforming to IS:2202 | Sqm | 2,095.00 |
| BMT-N.23 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 40 mmthick conforming to IS:2202 | Sqm | 2,467.00 |
| BMT-N.24 | Supply and fixing of Cement Bonded Particle Board (IS 14276) cup board frames and shutters and using 16mm Cement Bonded Particle Board duly painted both sides with one coat of primer and two coats of synthetic / enamel paint of approved shade and brand including fixing of hardware like M.S. powder coated Piano hinges of size 18mm x 18mm, brass ball catches, Aluminum tower bolts and handles , Godrej locks, Fevicol, screws and nails including cost and conveyance of all materials, labor charges, all incidental and operational charges etc., complete for finished item of work at site as per the directions of Engineer in Charge | Sqm | 2,651.00 |
| BMT-N.25 | Supply and fixing Cement Bonded Particle Board (IS 14276) single door shutter using with 16MM Cement Bonded Particle Board with allround "U" section of size 12mmx18mmx12mm made from 0.6 mm thick galvanized, color quoted cold rolled steel profiles with necessary screws fixed at every 304.8 mm intervals. The cost inclusive of MS Nickel coated Aldrops of size 255 mm long 2 Nos., 200 mm long tower bolts 1 No., 125 mm handles 2 Nos. 300 mm long "T" hinge cost and conveyance of all materials at site and applying 1 coat primer, 1 coat of luppum and 2 coats of synthetic enamel paint as per approved design for finished item of work | Sqm | 2,239.00 |
| BMT-N.26 | Supply and fixing of Cement Bonded Particle Board(IS 14276) door shutters using with 16MM Cement Bonded Particle Board with all round style “U” size of 20mmx18mm x20mm made from 0.6mm thick galvanized pre painted cold rolled steel profiles with Cement Bonded Particle Board separating two shutter with 30mmx18mmx30mm Stepped lipping with necessary screws fixed at every 1’ 0” (304.8mm) intervals. Ms Nickel coated 250 mm long aldrops 2 no’s, MS powder coated 250mm long tower bolt 2no’s , & 2no’s MS powder coated 125 mm long grip handle. Including cost and conveyance of all materials at site and applying one coat of primer, 2 coats of lappum and 2 coats of synthetic enamel paint as per approved design for finished item of work | Sqm | 2,256.00 |
| BMT-N.27 | Supply and fixing of Cement Bonded Particle Board (IS 14276) LAM double door shutter using 16 MM CEMENT BONDED PRELAMINATED PARTICLE BOARDS with all round “U” section size of 20mm x 18mm x 20mm made from 0.6mm thick galvanized prepainted cold rolled steel profiles with Cement Bonded Particle Board (IS 14276) LAM separating two shutter with 30mm x 20mm x 30mm stepped lipping with necessary screws fixed at every 1’0” (304.8mm) intervals. The cost inclusive of MS Nickel coated 250mm long a drops 2no’s, MS powder coated 125mm long grip handle, 2 no’s M.S.P.C. Door stopper. Including cost and conveyance of all materials at site labour charges etc., complete finished item of work | Sqm | 2,239.00 |
| BMT-N.28 | Providing and fixing of door frame made from cold roll formed sections made of galvanized (Base steel as per IS277 with zinc of 120 Gms/sqm) colour coated steel sections with total coated thickness of 1mm, primer coated with epoxy primer coat of 5-7 microns thick, finish paint with polyester paint of 12-16 microns. The Section for door frame is to be filled with polyurethane (P.U) form of 40kg/m3. Overall size of frame section should be of 50mm x 50mm. With necessary corner brackets, stiffeners, hinges, and screws. Cement Bonded particle board shutter “Single Leaf” with all round styles “U” section of size 12m x 18m x 12mm made from 0.6 mm thick galvanized, colour coated cold rolled steel profiles with 16mm thick Cement Bonded particle Board with necessary screws fixed at every 1’0” (304.8mm) intervals. The cost inclusive of MS nickel coated Aldrop of size 250mm long 2nos. 200mm long tower bolt 1no., 125mm handles 2nos., cost and conveyance of all materials at site and applying one coat primer , one coat of luppum and two coats of synthetic enamel paint as per approved design | Sqm | 4,900.00 |
| BMT-N.29 | Supply and fixing of Cement Bonded Particle Board (IS 14276) box type cup board using Cement Bonded Particle Board for making frame of size 100mm x 35mm using two sandwiched 16MM boards, one Cement Bonded Particle Board and one CEMENT BONDED PRELAMINATED PARTICLE BOARDS with plain 35mm wood lipping. The Shutters are made of 16MM thick CEMENT BONDED PRELAMINATED PARTICLE BOARDS (PreLaminated Cement Bonded Particle Board) of approved shade inclusive of hardware like M.S. powder coated Piano hinges of size ¾” x ¾” , Aluminum powder coated handles of size 4” (101.6mm), Aluminum tower bolt 4” (101.6mm) Godrej locks, screws, wood lipping and Fevicol etc., complete finish item of work | Sqm | 4,273.00 |
| BMT-N.30 | Supply and fixing of CEMENT BONDED PRELAMINATED PARTICLE BOARDS door shutter made out of U sections of size 12x14x12 made from 0.6mm thick pps sections with 12MM CEMENT BONDED PRELAMINATED PARTICLE BOARDS with necessary screws fixed at every 1’.0”interwells. The hardware consists of 250mm long aldrop – 2 Nos.150mm Handle 1 No , 150 mm long ms powder coated tower bolt 1 no. nickle coated. The cost is inclusive of all incidentals, labor transportation charges | Sqm | 2,672.00 |
| BMT-N.31 | Supply and fixing of door shutters made of rigid PVC extruded hollow section of 20mm X 200 mm with the wall thickness of 1.0mm +/ 0.1mm equally divided into 4 no's with tongue and groove locking arrangements. The shutter frame is made of 30mm X 79mm with the wall thickness of 1.5mm +/0.15mm section mitrecut and joined at 4 corners with 125mm X 225mm plastic brackets. The shutter shall be horizontally reinforced with 2 no's of 8mm PVC rods. Teak wood batons shall be reinforced inside the door shutter during the fabrication of the door shutter at those points wherever the hardware is fixed onto the door shutter | Sqm | 1,980.00 |
| BMT-N.32 | Supply and fixing of door frame made of hollow extruded PVC section having dimensions of 40 X 57mm with the wall thickness of 2mm +/ 0.2mm duly reinforced with seasoned wood plank at the hinges side. The door frame top 2 corners shall be metricut/ welded. PVC DOOR FRAME | Rm | 276.00 |
| BMT-N.33 | Supply and fixing of door frame made of hollow extruded PVC section having dimensions of 40 X 46 mm with the wall thickness of 2mm +/ 0.2mm duly reinforced with seasoned wood plank at the hinges side. The door frame top 2 corners shall be mitre cut/welded | Rm | 255.00 |
| BMT-N.34 | Supply & fixing of Door frames made of all formed sections of 1.25mm thick CRCA section, size should be 50x60mm with 32mm rebate. The corner of the frame should be welded. The frame should be painted with one coat of primer and finished painted with pure polyester paint. The frame should be provided with approved quality butt hinges of 3 Nos. complete for finished item.: Single shutter 3'0" x 7'0" (914.4x2133.6mm) outer frame section size of 50 x 60 mm | Rm | 310.00 |
| BMT-N.35 | Supply & fixing of Door frames made of all formed sections of 1.25mm thick CRCA section, size should be 50x60mm with 32mm rebate. The corner of the frame should be welded. The frame should be painted with one coat of primer and finished painted with pure polyester paint. The frame should be provided with approved quality butt hinges of 3 Nos. complete for finished item.: Double shutter 5'0" x 7'0" (1524 x 2133.6mm) outer frame section size of 50 x 60 mm | Rm | 310.00 |
| BMT-N.36 | Supplying & fixing of Door frame made of roll formed section of 1.25 mm thick CRCA section, size should be 50 x 60 mm with 32 mm rebate. The corner of the frame should be welded. The frame should be painted with one coat of primer and finished painted with pure polyester paint. The frame should be provided with approved quality butt hinges of 3 Nos. Complete for finished item of work.: Single shutter 3'0" x 7'0" (914.4x2133.6mm) outer frame section size of 50 x 75 mm | Rm | 350.00 |
| BMT-N.37 | Supplying & fixing of Door frame made of roll formed section of 1.25 mm thick CRCA section, size should be 50 x 60 mm with 32 mm rebate. The corner of the frame should be welded. The frame should be painted with one coat of primer and finished painted with pure polyester paint. The frame should be provided with approved quality butt hinges of 3 Nos. Complete for finished item of work.: Single shutter 5'0" x 7'0" (1524x2133.6mm) outer frame section size of 50 x 75 mm | Rm | 350.00 |
| BMT-N.38 | Providing and fixing door frames fabricated from sections made of galvanized steel powder coated (base steel as per IS 513, galvanised as per IS 277 with zinc of 120 grams / square metre), the factory made section are powder coated with pure polyester powder of 50-60 microns thick with total coated thickness of 1.25 mm, size of door frame section is of 105 x 60 mm with a rebate of 38 mm to accommodate 35 mm thick door shutter, with groove to insert gasket in the frame section, frame section filled with polyurethane foam, | Rm | 956.00 |
| BMT-N.39 | Providing and fixing of door frames factory made, internal door frames without threshold, fabricated from pre painted cold roll formed section 100 mm x 60 mm made of galvanized (base steel as per IS513 ‘D’ quality galvanized as per IS277 with Zinc of 120 Gms/sqm) steel colour coated sections with total coated thickness of 1 mm primer coated with epoxy primer of 5-7 microns thick finish painted with polyester paint of 12- 16 microns and back coated with alkyd backer of 5-7 microns, the frame section filled with polyurethane (PU Foam) of 40 kg/Cu.m and the sections cut to length and mitre joined by means of 1.25 mm thick CRCA electroplated corner brackets of size 75 x 75 mm and 1.25 mm thick electroplated stiffeners of size 150 mm for fixing hold fasts and hinges with MS Powder coated fittings a) 6 Nos M.S. Z Type hold fasts made of 30 mm x 3 mm MS flat of 230 mm long, 3 Nos each size expandable PVC covered screw type fasteners b) 2.5 mm x 300 mm long ‘T’ hinges /2.5 mm x 50 mm x 50 mm x 100 mm two way but hinges (3 Nos for single leaf or 2 Nos for Double leaf/leaf) c) 12 mm dia MS tie rod at bottom with necessary size of nuts on either side | Rm | 624.00 |
| BMT-N.44 | Supplying and fixing door shutter, with shutter frame and infill panel made from PVC material conforming to IS: 10151-1982, the shutter frame made out of PVC extruded sections having overall dimension of 47 mm x 33 mm with wall thickness of 1.2mm + 0.3mm with usual process variation, the shutter frame with tapered shape to provide better grip to the infill panel end to drain out the water The Infill panel is made out of PVC Sections having Overall Dimensions of 200 mm x 20 mm with wall thickness of 1mm + 0.2mm, the shutter frames mitre cut and joined at the corner, by providing Polymeric “ L” type corners to take hardware & fixtures fixed with 10 20mm counter sunk fully threaded parallel shank steel screws, all the hardware locations reinforced with special polymeric bars as per drawings, stickers showing locations of different hardware pasted on the shutter, the infill panels joined by tongue and groove method | Sqm | 1,168.00 |
| BMT-N.45 | Providing & Fixing of Scientific Doors with metal door frames and door shutters made of galvanize steel (base steel as per IS 513 of 0.58 mm thick D quality, galvanized as per IS 277 with Zinc of 120 GSM)coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability/Epoxy polyester powder for powder coating paint thickness 50-60 microns (Dry film thickness) outer frame section of 100 x 58 mm x 1.2 mm thick, shutter section of 0.80 mm thick galvanized steel sheet pressed (roll formed) for 46mm thick fully flush, double skin door shell seam joints at stile edges, infill of honeycomb kraft paper used to give the required | Sqm | 11,020.00 |
| BMT-N.46 | Providing & Fixing of Scientific Doors with metal door frames and door shutters made of galvanize steel (base steel as per IS 513 of 0.58 mm thick D quality, galvanized as per IS 277 with Zinc of 120 GSM). coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability/Epoxy polyester powder for powder coating paint thickness 50-60 microns (Dry film thickness) outer frame section of 100 x 58 mm x 1.2 mm thick, shutter section of 0.80 mm thick galvanized steel sheet pressed (roll formed) for 46mm thick fully flush, double skin door shell seam joints at stile edges, infill of honeycomb kraft paper used to give the required rigidity and effective acoustic insulation with 6” Tower bolt – 2 Nos., 6” D handles – 2 Nos., 10” Aldrop – 1 No., Butt Hinges – 6 Nos, Mortise Lock of approved quality – 1 No, frames fixed to the concrete/masonry wall by means of self expanding screws complete for finished item of work for Double leaf Door | Sqm | 11,500.00 |
| BMT-N.47 | Molded panel solid core flush doors using water-resistant hardwood Fiber HDF / MDF Fiber boards skins of 2.5 mm thick doors 30 mm thick | Sqm | 1,867.00 |
| BMT-N.48 | Moulded panel solid core flush doors using waterresistant hardwood Fiber HDF / MDF Fiber boards skins of 2.5 mm thick doors 35 mm thick | Sqm | 2,068.00 |
| BMT-N.49 | Solid core membrane flush doors using rigid PVC membrane of 0.3 mm thick of different elegant shades doors 30 mm thick | Sqm | 1,538.00 |
| BMT-N.50 | Solid core membrane flush doors using rigid PVC membrane of 0.3 mm thick of different elegant shades doors 35 mm thick | Sqm | 1,650.00 |
| BMT-N.51 | Providing & fixing 30 mm thick solid panel PVC door shutter consisting of frame made out of 19 guage M.S tube of 19 x 19 mm for stiles, top & bottom rail, with a coat of primer of approved make. M.S. Frame covered with 5 mm thick heat moulded PVC “C” channel of size of 30 x 50 mm forming stiles, 5 mm thick 75 mm wide PVC sheet for top, lock & bottom rail on either side 20 mm wide cross PVC sheet as gap insert for top & bottom rail, panelling of 10mm(+/-)( 5mm+5mm)” thick PVC sheet fitted in the M.S. frame welded /sealed to the stiles, on either side joined together with solvent cement adhesive etc., additional 5 mm thick | Sqm | 3,439.00 |
| BMT-N.52 | Supply & Fixing SOLID STEEL DOOR door shutter made out of G I Precoated Sheet with an average wall thickness of 0.35 mm on both sides. MS Tube having dimensions of 19 x 19 mm is inserted along the hinge side of the door, core of the door shutter filled with High Density Polyurethane foam injected with the help of hydraulic injection method, four sides of the door covered with G I Precoated Sheet and the hardware locations reinforced with suitable wooden blocks as per drawing and stickers indicating location of the hardware pasted at appropriate places, etc complete | Sqm | 1,904.00 |
| BMT-N.53 | Supplying & fixing SINGLE PANEL 30 mm thick PVC DOOR, door shutters with shutter frame and Infill panel made from PVC material, the shutter frame made out of PVC extruded sections having overall dimensions of 6 0mm x 30 mm with wall thickness of 1.3 mm ± 0.3 mm, with the Infill panel made out of multi chambered seamless hollow PVC extruded panel having overall dimensions of 610 mm x 20 mm having wall thickness 1 mm ± 0.2 mm with the shutter frame meter cut and joined at corners and all the hardware locations reinforced with special polymeric bars as per drawing including providing special PVC braket on hinge side, etc complete | Sqm | 2,931.00 |
| BMT-N.54 | Providing & fixing internal prelaminated PVC door frame of size 100 x 45 mm with a wall thickness of 5mm, made of extruded 5 mm Prelam PVC foam sheet, mitred cut at two corners and joined with two nos. of 150mm long brackets of 15 x 15 mm MS square tube, two vertical door profiles reinforced with 40 x 20 MS Tube of 19 guage throughout the frame and the door frame fixed to the wall using 65/100mm long MS screws through the | Rm | 773.00 |
| BMT-N.55 | Supply & Fixing of Powder Coated Mild Steel doors, frames & shutters made of Skin pass galvanized Iron sheet conforming to Base Steel as per IS 513 “D” Quality, Galvanized as per IS 277 with Hot Zinc Coating of 120 grams / Sq.Mtr with powder coating of thickness 6065 Microns, frame with 1.2mm thick Skin pass Galvanized Iron sheet formed to single rebate profile of ize 100 mm X 58 mm and filled with infill Polyurethane foam, the Door Shutters are with 0.80 mm thick Skin pass Galvanized Iron Sheet formed to provide a 46 mm thick fully flush, double skin door shell with Lock Seam joints at stile edges, fitted with infill of Honeycomb Kraft Paper and coated with polyester powders of Pure polyester/ epoxy polyester or polyurethane powder for powder coating of thickness 60 – 65 microns and are coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability, the Shutter provided with 6 MM clear float vision glass in Circular, Square or Rectangular shapes, Stainless Steel Ball Bearing Butt Hinges 3 mm thick fixed flush to the frame and shutter (Profile 102x76x3mm thick).Mortise Sash Lock with Lever Handles, Mortise Dead Bolt, etc for industrial, commercial, residential, cleanroom applications | Sqm | 10,100.00 |
| BMT-N.56 | Supply & Fixing of Stainless steel doors, frames & shutters made of stainless steel grade 304 of hairline finish, frame with 1.2mm thick formed to single rebate profile of ize 100 mm X 58 mm and filled with infill Polyurethane foam, the Door Shutters are with 0.80 mm thick Stainless steel Sheet formed to provide a 46 mm thick fully flush, double skin door shell with Lock Seam joints at stile edges, fitted with infill of Honeycomb Kraft Paper, the Shutter provided with 6 MM clear float vision glass in Circular, Square or Rectangular shapes, Stainless Steel Ball Bearing Butt Hinges 3 mm thick fixed flush to the frame and shutter (Profile 102x76x3mm thick).Mortise Sash Lock with Lever Handles, Mortise Dead Bolt, etc for industrial, commercial, residential, cleanroom applications | Sqm | 17,400.00 |
| BMT-N.57 | Supply & Fixing of Powder Coated Fire Rated doors, frames & shutters made of Skin pass galvanized Iron sheet conforming to Base Steel as per IS 513 “D” Quality, Galvanized as per IS 277 with Hot Zinc Coating of 120 grams / Sq.Mtr with powder coating of thickness 6065 Microns, frame with 1.2mm thick Skin pass Galvanized Iron sheet formed to double rebate profile of ize 143 mm X 58 mm with maximum bending radius of 1.4 mm and filled with infill Polyurethane foam, the Door Shutters are with 0.80 mm thick Skin pass Galvanized Iron Sheet formed to provide a 46 mm thick fully flush, double skin door shell with Lock Seam joints at stile edges, fitted with infill of Honeycomb Kraft Paper and coated with polyester powders of Pure polyester/ epoxy polyester or polyurethane powder for powder coating of thickness 60 – 65 microns and are coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability, the Shutter provided with 6 MM clear float vision glass in Circular, Square or Rectangular shapes, Stainless Steel Ball Bearing Butt Hinges 3 mm thick fixed flush to the frame and shutter (Profile 102x76x3mm thick).Mortise Sash Lock with Lever Handles, Mortise Dead Bolt, etc for 120 minutes Fire Rated door conforming to IS:3614 (Part2) 1992 | Sqm | 14,595.00 |
| BMT-N.58 | Supply & Fixing of Powder Coated Fire Rated doors, frames & shutters made of Skin pass galvanized Iron sheet conforming to Base Steel as per IS 513 “D” Quality, Galvanized as per IS 277 with Hot Zinc Coating of 120 grams / Sq.Mtr with powder coating of thickness 6065 Microns, frame with 1.2mm thick Skin pass Galvanized Iron sheet formed to double rebate profile of ize 143 mm X 58 mm with maximum bending radius of 1.4 mm and filled with infill Polyurethane foam, the Door Shutters are with 0.80 mm thick Skin pass Galvanized Iron Sheet formed to provide a 46 mm thick fully flush, double skin door shell with Lock Seam joints at stile edges, fitted with infill of Honeycomb Kraft Paper and coated with polyester powders of Pure polyester/ epoxy polyester or polyurethane powder for powder coating of thickness 60 – 65 microns and are coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability, the Shutter provided with 6 MM clear float vision glass in Circular, Square or Rectangular shapes, Stainless Steel Ball Bearing Butt Hinges 3 mm thick fixed flush to the frame and shutter (Profile 102x76x3mm thick).Mortise Sash Lock with Lever Handles, Mortise Dead Bolt, etc for 60 minutes Fire Rated door conforming to IS:3614 (Part2) 1992 | Sqm | 13,806.00 |
| BMT-N.59 | Supply & Fixing of Stainless steel Fire Rated doors, frames & shutters made of Stainless steel of 304 grade hairline finish, frame with 1.2mm thick Stainless steel of 304 grade hairline finish sheet formed to double rebate profile of ize 143 mm X 58 mm with maximum bending radius of 1.4 mm and filled with infill Polyurethane foam, the Door Shutters are with 0.80 mm thick Stainless steel of 304 grade hairline finish Sheet formed to provide a 46 mm thick fully flush, double skin door shell with Lock Seam joints at stile edges, fitted with infill of Honeycomb Kraft Paper and coated with polyester powders of Pure polyester/ epoxy polyester or polyurethane powder | Sqm | 22,500.00 |
| BMT-N.60 | Supply & Fixing of Stainless steel Fire Rated doors, frames & shutters made of Stainless steel of 304 grade hairline finish, frame with 1.2mm thick Stainless steel of 304 grade hairline finish sheet formed to double rebate profile of ize 143 mm X 58 mm with maximum bending radius of 1.4 mm and filled with infill Polyurethane foam, the Door Shutters are with 0.80 mm thick Stainless steel of 304 grade hairline finish Sheet formed to provide a 46 mm thick fully flush, double skin door shell with Lock Seam joints at stile edges, fitted with infill of Honeycomb Kraft Paper and coated with polyester powders of Pure polyester/ epoxy polyester or polyurethane powder for powder coating of thickness 60 – 65 microns and are coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability, the Shutter provided with 6 MM clear float vision glass in Circular, Square or Rectangular shapes, Stainless Steel Ball Bearing Butt Hinges 3 mm thick fixed flush to the frame and shutter (Profile 102x76x3mm thick).Mortise Sash Lock with Lever Handles, Mortise Dead Bolt, etc for 60 minutes Fire Rated door conforming to IS:3614 (Part2) 1992 | Sqm | 20,150.00 |
| BMT-N.61 | Supply & Fixing of Lead Lined Clean room doors frames and shutters made of Skin pass galvanized Iron sheet (Conform to Base Steel as per IS 513 “D” Quality, Galvanized as per IS 277 with Hot Zinc Coating of 120 grams / Sq.Mtr).with powder coating of thickness 6065 Microns, frame of 1.60mm thick galvanized steel sheet (Conform to IS 277) formed to Single/double rebate profile of size 100mm X 58mm/ 143x58mm, door frames with a single / multi Layer of Lead sheet varying thickness from 3mm /1mm to 2mm depends on radiation level, the shutter with 1.2 mm thick Galvanized Steel Sheet (Conform to IS 277) formed to provide a 46mm thick fully flush, double skin door shell with Lock Seam joints at stile edges with a single / multi Layer of Lead sheet varying thickness from 3mm /1mm to 2mm depends on radiation level, the lead sheets extend the full width and height of the door, Lead thickness is equal to the shielding in the adjacent wall, the door frames and door shutters are coated with polyester powders of Pure polyester/ epoxy polyester or polyurethane powder for powder coating of thickness 60 – 65 microns, coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability, hardware with Stainless Steel Ball Bearing Butt Hinges 3 mm thick fixed flush to the frame and shutter etc complete for finished item | Sqm | 17,088.00 |
| BMT-N.62 | Supply & Fixing of Lead Lined Stainless steel Clean room door frames and shutters made of Stainless steel grade of 304 hairline finish, frame with 1.60mm (16SWG) thick hairline finish Stainless steel grade of 304 formed to Single/double rebate profile of size 100 mm x 58mm/ 143 x 58 mm, door frames with a single / multi Layer of Lead sheet varying thickness from 3mm /1mm to 2mm depends on radiation level, the shutter with 1.2 mm thick hairline finish Stainless steel grade of | Sqm | 26,150.00 |
| BMT-N.63 | Supply and fixing of BOARD (conforming toIS 14862) door shutter with allround style “U” lipping size 15 x 18 x 15 mm made from 0.8 mm thick powder coated cold rolled steel profiles with 16 mm thick VBOARD with necessary screws fixed at 1’0” interval 250 mm long aldrops 2 nos. M.S. nickel coated 250 mm long 1 no. M.S. Tower Bolts Including cost and conveyance of all materials at site and applying 1 coat of primer, 2 coats of luppum and 2 coats of synthetic enamel paint as per approved design for finished item of work | Sqm | 1,607.00 |
| BMT-N.64 | Supply and fixing of BOARD (conforming toIS 14862) 12 mm thick door shutter of size 6’0” x 2’6” withall round style “U” lipping size 15 x 14 x 15 mm made from 0.8 mm thick powder coated cold rolled steel profiles with necessary screws fixed at 1’0” interval 250 mm long aldrops 2 nos. M.S. nickel coated 250 mm long 1 no. M.S. Tower Bolts Including cost and conveyance of all materials at site and applying 1 coat of primer, 2 coats of luppum and 2 coats of synthetic enamel paint as per approved design for finished item of work | Sqm | 1,574.00 |
| BMT-N.65 | Providing and fixing frame made from 1.2 mm powder coated cold rolled steel profiles of overall section size of 60 mm x 45 mm with 21 mm rivet for shutter with necessary stiffeners hinges and screws. BOARD (IS 14862) shutter with allround style “U” lipping of size 15 x 18 x 15 mm made from 0.8 mm thick CRCA powder coated steel profile with 16 mm thick Vboard with necessary screws fixed at every 1’0” interval 250 mm long aldrops 2 nos. M.S. nickel coated 250 mm long 1 no. M.S. Tower Bolts Including cost and conveyance. One coat of primer, 2 coats of luppum and 2 coats of synthetic enamel paint as per approved colour, labour charges etc | Sqm | 2,196.00 |
| BMT-N.67 | A) Specification for Foamed PVC Door Frame & ABS Shutters: Providing of Factory made prelaminated FPVC (Foamed Polyvinyl Chloride) Door frame of the size 105x40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre joined with 6 Nos. of 50mm long screw. The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners of 3 no's to be provided for each vertical member,GI stiffners of ("U" chanel of size 29x9x1mm, 150mm long) 3 no's at hinge point,Frame reinforcement of("U" GI chanel of size 46x22x.06mm),Bottom tie rod of ("U" GI chanel size of 15x15x1mm) etc. complete as per manufacturers specification for finished item of work. Maximum door frame size : 980 x 2070 . B) Providing of 35mm thick Facotry made Prelaminated ABS (Acrolynitrile Butadyne Styrene) Door shutter moulded in different designs, consisting of all round Frame made out of water proof solid foam PVC bar of size 20x32mm, reinforced by 32x 32mm 2 nos. for vertical made out of LVL (Laminated Veneer Lumber), core material of 32 mm thick high density craft paper honey comb board, sandwiched on both sides with prelaminated ABS sheet thickness of 1.5mm . PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges 3 Nos. for each shutter and ISI make S.S round lock completes for finished item of work. Maximum shutter size of : 910 x 2030 mm | Each | 16,013.00 |
| BMT-N.68 | Providing of 35mm thick Facotry made Prelaminated ABS (Acrolynitrile Butadyne Styrene) Door shutter moulded in different designs, consisting of all round Frame made out of water proof solid foam PVC bar of size 20x32mm, reinforced by 32x 32mm 2 nos. for vertical made out of LVL (Laminated Veneer Lumber), core material of 32 mm thick high density craft paper honey comb board, sandwiched on both sides with prelaminated ABS sheet thickness of 1.5mm . PVC edge banding of size 0.45mm on the vertical sides.for each shutter and ISI make S.S round lock complete for finished item of work | Sqm | 7,350.00 |
| BMT-N.69 | Supply and fixing of Bath room / Toilet door shutter with 16mm laminated (IS 14276) door shutter with allround ‘U’ lipping of PPS section of size 12mm X 18mmX 12mmX0.6mm thickness with a hardware of 12mm dia X200mm long aluminum aldrop – 2 nos( ISI make)2 No of 125mm long handles(ISI make) and also 3 no Of IS304 grade Patee Hinges 3mmX12mmX180mm long with pole receiver of 10mm dia pole X40mm long welded on 2mm X40mm(ss304) plates works as receiver for RT patte hinges. The price inclusive of all material at site | Sqm | 2,877.00 |
| BMT-N.70 | Supply and fixing of toilet door shutter with frame made of M.S. door frame of 5mmX48mmX48mm (L angel) as all round frame the frame is coated with one coat of red oxide and two coats of enamel of approved color. For shutter and the shutter is made with 16mm laminatedshutter with allround ‘U’ Lipping of PPS section of 12mmX18mmX12mmX0.60mm, along hardware of 200m long and 12mm dia aluminum aldrop( ISI make)2 Nos, 2Nos of 125m m handle, 3 Nos of RT patte hinges IS 304gr SS 2mmX12mmX180mm long with a pole receiver of 10mmDia X 40mm by welded on 3mmX40mm SS 304, plate it works as receiver for RT Patee hinges it is welded to M.S. angle . M.S. angle will be fixed to wall of self expandable screws and caps | Sqm | 4,460.00 |
| BMT-N.71 | Supply and fixing of cupboard shutter using teakwood scantling of size 50mm X50mm teakwood as outer frame and 50mm X 30 mm of size teakwood for shutter frames , 8mm thick Bison Lam as panel to each shutter consist of 2 Nos 75mm long tower bolt – 2 nos 75 mm big handle the and other shutter will have 1 no of cupboard lack , 1 No of 75 mm long handle and 75mm10mmX1mm thick SS hinges 2 Nos for each shutter. The above frame will be fixed to the wall with screws, the rate inclusive of screws, handle, etc., complete at site of work | Sqm | 4,500.00 |
| BMT-N.73 | Door shutter with shutter frame and Infill panel made from PVC material conforming to IS: 10151:1982. The shutter frame is made out of PVC extruded sections having overall dimensions of 100mm X 30mm, with two self extruded grooves at 40mm & 50mm on front surface. The Infill panel is made out of multi chambered seamless hollow PVC extruded panel having overall dimensions of 610 mm X 20 mm. The shutter frame shall be meter cut and joined at corners by means of plastic brackets. Stickers showing locations of different hardware will be pasted on the shutter. ALL Dimensions are in MM | Sqm | 1,168.00 |
| BMT-N.74 | The shutter frame made out of PVC extruede section having overall dimensions of 59mm x 24mm with wall thickness of 1.0mm +/0.3mm with usual process variation corresponding to the Sintex Code No.DWUF302. The shutter frame is given tampered shape to provide better grip to the infill panel and to drain out the water.The infill panel is made out of seamless one piece multi chambered PVC extruded section having overall dimension of 610mm x 20mm with wall thickness of 1mm +/0.2mm with usual process variation corresponding to the Sintex code No.SPUF128. The shutter frame shall be mitre cut and joined at the corner polymeric “L’ Type corners shall be provided at the corners to take up hardwares & fixtures and shall be fixed with 19 x 8mm counter sunkfully threaded parallel shank steel screws. All the hardware locations shall be reinforced with special polymeric Bars | Sqm | 2,250.00 |
| BMT-N.79 | Supply and fixing of CEMENT BONDED PARTICLE BOARD double door shutter using 16 MM CEMENT BONDED PARTICLE BOARD LAM with all round “U” section size of 20mm x 18mm x20mm made from 0.6mm thick galvanized prepainted cold ro steel profiles with CEMENT BONDED PARTICLE BOARD LAM separating two shutter with 30mm x lled 20mm x 30mm stepped lipping with necessary screws fixed at every 1’0” (304.8mm) intervals. The cost inclusive of MS Nickel coated 250mm long aldrops 2no’s, MS powder coated 125mm long grip handle, 2 no’s M.S.P.C. Door stopper. Including cost and conveyance of all materials at site labor charges etc., complete finished item of work | Sqm | 3,250.00 |
| BMT-N.80 | Powder Coated Mild Steel Hallow single rebate door frames manufactured using cold roll formed process steel sheet of 1.25 mm thick bright (Cold Rolled Close Annealed (CRCA) and profile size of 105 x 60 mm conforming to IS 4351 2003 including pretreatment, Galvanized as per IS:277, zinc phosphating finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability/Epoxy polyester powder for powder coating paint thickness 60 – 65 microns(Dry film thickness)Stainless Steel Ball Bearing Butt Hinges 3 mm thick fixed flush to the frame with Hinges, Base Ties, Holdfast Lugs, Mortar Guards, shock absorbers and provision for Tower Bolts, Aldrops, Lock & Strike plates etc. for both single and double shutter doors | Rm | 893.00 |
| BMT-N.81 | Mild Steel Hallow single rebate general purpose door frames manufactured using cold roll formed process steel sheet of 1.25 mm thick bright (Cold Rolled Close Annealed (CRCA) and profileB of size 105 x 60 mm conforming to IS 4351 2003 including pretreatment, phosphating with Hinges, Base Ties, Holdfast Lugs, Mortar Guards, shock absorbers and provision for Tower Bolts, Aldrops, Lock & Strike plates etc. for both single and double shutter doors | Rm | 494.00 |
| BMT-N.82 | Supply and fixing of factory made Bathroom door frames without threshold, fabricated from prepainted cold roll formed section 50mm x 50 mm made of galvanized (base steel as per IS – 513 ‘D’ quality, galvanized as per IS277 with Zinc of 120 Gms/sqm) steel colour coated sections with total coated thickness of 1 mm, primer coated with epoxy primer of 5-7 microns thick, finish painted with polyester paint of 12-16 microns and back coated with alkyd backer of 5-7 microns and the frame section filled with polyurethane (P.U. Foam) of 40 Kg/Cum; and the sections cut to length and mitre joined by means of 1.25mm thick CRCA electroplated corner brackets of size 75 x 75 mm and 1.25mm thick electroplated stiffeners of size 150mm for fixing hold fasts and hinges together with the following MS Power coated fitting (Supply and fixing) of approved make. (a) 6 Nos M.S. Z. Type hold fasts made of 30mm x 3 mm MS flat of 230mm long, 3 Nos each side expandable PVC covered screw type fasteners. (b) 2.5 mm x 300 mm long ‘T’ hinges / 2.5mm x 50 mm x 100mm two way but hinges (3 Nos for single leaf or 2 Nos for Double leaf /leaf ) (c) 12 mm Dia MS tie rod at bottom with necessary size of nuts on either side | Rm | 503.00 |
| BMT-N.83.A | Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM.Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member | Rm | 601.00 |
| BMT-N.83.B | Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM.Door Frame section of 45x90 MM . The two Vertical members are to be joined together with the horizontal member using 8x60 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member | Rm | 844.00 |
| BMT-N.83.C | Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM.Door Frame section of 63.5x100 MM .The two Vertical members are to be joined together with the horizontal member using 8x75 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member | Rm | 1,001.00 |
| BMT-N.84.A | Providing and fixing factory made uPVCCasement door with 3D hinges made of (big series) frame 67x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) | Sqm | 9,062.00 |
| BMT-N.84.B | Providing and fixing factory made uPVCCasement door with top hung ventilator with 3D and S.S. frictionhinges (400 x 19 x 1.9 mm) made of (big series) frame | Sqm | 9,356.00 |
| BMT-N.85.A | Providing and fixing factory made uPVC any colour sliding glazed doorcomprising of uPVC multi chambered frame with inbuilt roller track andsash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanizedmild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVCextruded glazing beads, uPVC extruded interlock and uPVC extrudedInline sash adaptor (if required), EPDM gasket/TPV, wool pile, zinc alloy(white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmissiongear with keeps, zinc alloy (white powder coated) cresent lock (ifrequired), stainless steel (SS 304 grade) body with adjustable doublenylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steelscrews etc. Profile of frame & sash shall be mitred cut and fusion weldedat all corners, including drilling of holes for fixing hardware's and drainageof water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backerrod of required size and of approved quality, all complete as per approveddrawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes,wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Variationin profile dimension in higher side shall be accepted but noextra payment on this account shall be made.Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thicknessof 2.3 ± 0.2 mm and single glazing bead / double glazingbead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) | Sqm | 6,652.00 |
| BMT-N.85.B | Providing and fixing factory made uPVC any colour sliding glazed doorcomprising of uPVC multi chambered frame with inbuilt roller track andsash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanizedmild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVCextruded glazing beads, uPVC extruded interlock and uPVC extrudedInline sash adaptor (if required), EPDM gasket/TPV, wool pile, zinc alloy(white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmissiongear with keeps, zinc alloy (white powder coated) cresent lock (ifrequired), stainless steel (SS 304 grade) body with adjustable doublenylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steelscrews etc. Profile of frame & sash shall be mitred cut and fusion weldedat all corners, including drilling of holes for fixing hardware's and drainageof water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backerrod of required size and of approved quality, all complete as per approveddrawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes,wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Variationin profile dimension in higher side shall be accepted but noextra payment on this account shall be made.Three track three panels sliding door with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of(big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) | Sqm | 8,220.00 |
| BMT-N.86 | Providing and fixing of factory made of High Density High MoistureResistant Wood Fiber (HDHMR) single shutter Duradoor made up of FRAME: Door frame manufactured with High Density High MoistureResistant Wood Fiber (HDHMR) of 36mm width x 100mm depth , laminated with 0.2mm thick PVC Foil using hot press andPUR adhesive, fitted with Gasket for energy efficiency and noise protection,affixed to the wall using high strength expandable PU Foam/ selfexpandable wall fixing screws.Max dimensions in MM of 280 (depth) x 2440 (height)SHUTTER: Factory made 41mm thick shutter sandwiched with High Density High Moisture ResistantWood Fiber (HDHMR) of 5.5mm thick skinson both sides and HDHMR of 30mm thickness as skeleton,core of high density Honey Comb and Laminated Veneer Lumber (LVL) for holding the lock body andhardware, laminated with 0.2mm thick PVC Foil and edgebanded with 1mm thick PVCedgeband using hot press and PUR adhesives. Max dimensions in MM of 1200 (width) x 41(thickness) x 2400 (height), ARCHITRAVE: Factory made Architrave of size 80mm x 12mm fitted to premade grooves within the frame for addedaesthetics. Four design variants available, made with Density High Moisture Resistant Wood | Sqm | 11,939.00 |
| BMT-N.87 | Supply and fixing of Bath/Toilet Door frame and shutter with 8mm laminated (IS.15786)using with 50mmx35mmx1.3mmthick aluminum door frame of weight 220grm per Rft with a rebate of 30 mm for provision for shutter , shutter made with 45mmx25mmx1.3mm thick aluminum section of weight 210grms per Rft with 8mm groove to accommodate 8mm thick laminated (IS.15786) and shutter having 3nos of ss 304gr Butt hinges of 100mm long, 100mm aluminum handles 2nos, and also 2 nos of 200mmx12mm aluminum aldrops ,the rates inclusive of all labor fixing at site and 50microns Ivory powder coated for aluminum door frame and shutter sections etc complete finished item of work | Sqm | 5,787.00 |
| BMT-N.89 | Supply and fixing of SINGLE PANEL 30mm thick door shutters(NANDI or equivalent) made of rigid PVC extruded hollow section of 20mm X 635mm with the wall thickness of 1.Omm+/ 0.1mm. The shutter frame is made of 3OmmX79mm with the wall thickness of 1.5mm +/ 0.15mm section mitrecut and joined at 4 corners with 125mmX225mm plastic brackets. Teak wood batons shall be reinforced inside the door shutter during the fabrication of the door shutter at those points wherever the hardware is fixed on to the door shutter | Sqm | 2,920.00 |
| BMT-N.90 | Supply and fixing of door frame (NANDI or EQUIVALENT) made of hollow extruded PVC section having dimensions of 40 X 57mm with the wall thickness of 2mm +1 0.2mm duly reinforced with seasoned wood plank at the hinges side. The door frame top 2corners shall be metricut/ welded. PVC DOOR FRAME | Sqm | 257.00 |
| BMT-N.91 | Supplying & fixing SINGLE PANEL 30mm thick PVC DOOR frame (NANDI or EQUIVALENT), door shutters with shutter frame and Infill panel made from PVC material, the shutter frame made out of PVC extruded sections having overall dimensions of 105 mm x 30 mm with wall thickness of 1.3mm ± 0.3 mm, with the Infill panel made out of multi chambered seamless hollow PVC extruded panel having overall dimensions of 610 mm x 20 mm having wall thickness 1 mm ± 0.2 mm with the shutter frame meter cut and joined at corners and all the hardware locations reinforced with special polymeric bars/wooden Battens as per drawing including providing special PVC bracket/Wooden Battens on hinge side etc complete | Sqm | 3,039.00 |
| BMT-N.92 | Providing and fixing 28 30 MM thick solid Wood Polymer Composite(WPC) single extruded door shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame | Sqm | 3,688.00 |
| BMT-N.98 | Supply of factory made of Double Skin Pass Galvanized Powder Coated Single Rebate Doorframe and single shutter/Double shutter for General applications made of Double Skin Pass Galvanized Sheet confirming to Base Steel as per IS 513 of ‘D’ Quality Galvanized as per IS 277 with Zinc coating of 120 GSM , Pure polyester Powder Coated Paint of 60-65Microns(DFT)Thick. Frame: Single rebate Door Frame of size 100 mm X 78 mm with 1.00 mm thick Double Skin Pass Galvanized sheet Roll formed into Closed Box Profile with Suitable lockseam joints and proper stitching procedures having a Design Architrave of 20 mm width and Accommodate a 46 mm thick Door shutter and the sections cut to length , Miter joined with corner bracket and EPDM Gaskets using self expanding Screws . The Door frames are filled with an infill material of Polyurethane foam (PUF) of Density 32 to 36 kg / m3. Groove in Door Frame shall be provided to hold EPDM Gasket so that the Door shutters shall rest on the EPDM Gasket when the Door shutters are closed. EPDM gasket makes the Door weather resistant. The door frame shall be provided with hinge jamb, lock jamb, head jamb and with Suitable Anchors per frame. Door frame Stiffeners for Hinge: Stiffener of Skin pass Galvanized Sheet of 3 mm thick shall be welded to the pressed angle from inner side of the Door Frame and shutter using projection welding / Fixing with Screws from Gasket groove. Stiffener plate shall be threaded to the required size of machine screw (M6 × 20 CSK) conforming to IS 1365, 2.2/1.8 mm joggling depth on a 3 mm hinge plate. Door Frame Stiffener of pressed ‘C’ channels and Skin pass Galvanized steel Sheet of thickness 1.60 mm and of sufficient width and length or 1.2 mm thick (Skin pass Galvanized steel Sheet) sheet of required width and | Sqm | 10,360.00 |
| BMT-N.99 | Supply of factory made of Double Skin Pass Galvanized Powder Coated Single Rebate Door frame and Single shutter/Double shutter for Scientific applications made of Double Skin Pass Galvanized Sheet confirming to Base Steel as per IS 513 of ‘D’ Quality Galvanized as per IS 277 with Zinc coating of 120 GSM , Pure polyester Powder Coated Paint of 60-65 Microns (DFT) Thick. Frame : Single rebate Door Frame of size 100 mm X 78 mm with 1.00 mm thick Double Skin Pass Galvanized sheet Roll formed into Closed Box Profile with Suitable lockseam joints and proper stitching procedures having a Design Architrave of 20 mm width and accommodate a 46 mm thick Door shutter and the sections cut to length , Miter joined with corner bracket and EPDM Gaskets using selfexpanding Screws . The Door frames are filled with an infill material of Polyurethane foam (PUF) of Density 32 to 36 kg / m3. Groove in Door Frame shall be provided to hold EPDM Gasket so that the Door shutters shall rest on the EPDM Gasket when the Door shutters are closed. EPDM gasket makes the Door weather resistant. The door frame shall be provided with hinge jamb, lock jamb, head jamb and with SuitableAnchors per frame. . Door frame Stiffeners for Hinge: Stiffener of Skin pass Galvanized Sheet of 3 mm thick shall be welded to the pressed angle from inner side of the Door Frame and shutter using projection welding / Fixing with Screws from Gasket groove. Stiffener plate shall be threaded to the required size of machine screw (M6 × 20 CSK) conforming to IS 1365, 2.2/1.8 mm joggling depth on a 3 mm hinge plate. Door Frame Stiffener of pressed ‘C’ channels and Skin pass Galvanized steel Sheet of thickness 1.60 mm and of sufficient width and length or 1.2 mm thick (Skin pass Galvanized steel Sheet) sheet of required width and height as per the iron monger, shall be provided | Sqm | 10,370.00 |
| BMT-N.100 | Supply of factory made of Double Skin Pass Galvanized Powder Coated Single Rebate Door frame for general applications made of Double Skin Pass Galvanized Sheet confirming to Base Steel as per IS 513 of ‘D’ Quality Galvanized as per IS 277 with Zinc coating of 120 GSM , Pure polyester Powder Coated Paint of 6065 Microns (DFT) Thick. Frame: Single rebate Door Frame of size 100 mm X 78 mm with 1.00 mm thick Double Skin Pass Galvanized sheet Roll formed into Closed Box Profile with Suitable lockseam joints and proper stitching procedures having a Design Architrave of 20 mm width and accommodate a 46 mm thick Door shutter and the sections cut to length , Miter joined with corner bracket and EPDM Gaskets using selfexpanding Screws . The Door frames are filled with an infill material of Polyurethane foam (PUF) of Density 32 to 36 kg / m3. Groove in Door Frame shall be provided to hold EPDM Gasket so that the Door shutters shall rest on the EPDM Gasket when the Door shutters are closed. EPDM gasket makes the Door weather resistant. The door frame shall be provided with hinge jamb, lock jamb, head jamb and with Suitable Anchors per frame. Door frame Stiffeners for Hinge: Stiffener of Skin pass Galvanized Sheet of 3 mm thick shall be welded to the pressed angle from inner side of the Door Frame and shutter using projection welding / Fixing with Screws from Gasket groove. Stiffener plate shall be threaded to the required size of machine screw (M6 × 20 CSK) conforming to IS 1365, 2.2/1.8 mm joggling depth on a 3 mm hinge plate. Stiffeners for fittings and fixtures: Stiffener of pressed ‘C’ channels and Skin pass Galvanized steel Sheet of thickness 1.60 mm | Rm | 1,011.00 |
| BMT-N.101 | Supply of Factory made of Single Rebate Stainless Steel Door frame and Single shutter/ Double Shutter for Scientific applications made of Stainless Steel Grade 304 of Hairline Finish Frame : Single rebate Door Frame of size 100 mm X 78 mm with 1 mm thick Stainless Steel Grade 304 sheet Roll formed into Closed Box Profile with Suitable lockseam joints and proper stitching procedures having a Design Architrave of 20 mm width and accommodate a 46 mm thick Door shutter and the sections cut to length , Mitre joined with corner bracket and EPDM Gaskets using selfexpanding Screws . The Door frames are filled with an infill material of Polyurethane foam (PUF) of Density 32 to 36 kg / m3. Groove in Door Frame shall be provided to hold EPDM Gasket so that the Door shutters shall rest on the EPDM Gasket when the Door shutters are closed. EPDM gasket makes the Door weather resistant. The door frame shall be provided with hinge jamb, lock jamb, head jamb and with Suitable Anchors per frame | Sqm | 17,825.00 |
| BMT-N.102.A | For 73mm X 48mm size door frame | Rm | 775.00 |
| BMT-N.102.B | For of 98mm X 48mm size door frame | Rm | 1,032.00 |
| BMT-N.102.C | For of 98mm X 58mm size door frame | Rm | 1,293.00 |
| BMT-N.102.D | For of 128mm X 58mm size door frame | Rm | 1,616.00 |
| BMT-N.103 | Providing and fixing in position factory- made steel glazed main entrance hinged door , complete with steel frame, shutter, fixed glass side and top Panels, including all fittings, fixtures, hardware, fasteners and accessories, as per approved drawings, specifications and directions of Engineer-in-Charge. The door frame shall be manufactured from 1.0 mm thick galvanized plain skin pass (GPSP) sheet conforming to IS 513 ‘D’ quality and IS 277 with minimum 120 GSM zinc coating, roll- formed into 100 mm × 78 mm closed box single rebate profile with 20 mm decorative architrave on exposed faces, mitred at corners and assembled using corner brackets and self-expanding screws, internally filled with polyurethane foam (PUF) of density 32–36 kg/m³, and provided with continuous EPDM rubber gasket groove and gasket for air-tight sealing, suitable to accommodate hinged shutter along with fixed side and top glass panels as per site requirements. The door shutter shall be 46 mm thick, fully flush, double-skin construction, with both inner and outer skins made from 0.8 mm thick galvanized plain skin pass (GPSP) sheets, joined using lock-seam joints with U- shaped bent edges, internally filled with honeycomb kraft paper, and provided with stiffeners at hinge, lock and handle locations, suitable for accommodating glass vision panel wherever required as per approved drawings. Fixed glass side and top panels shall be formed using matching galvanized steel sections integrated with the main door frame, glazed with clear toughened glass of 6mm thickness fixed using gasket system, ensuring vibration-free, weather-tight installation, with all glass edges polished and safety compliant.The entire door assembly including frame, shutter and fixed panels shall be finished with factory- applied powder coating in approved shade, with coating thickness minimum 60 microns.Hardware: 1 pair of 10" D- handles,3 ball bearing butt hinges,1 mortise lock or 10" aldrop,1 six-inch tower bolt. Main entrance hinged door with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 18,372.00 |
| BMT-N.104.A | Providing and fixing in position factory- made Room entrance Steel door , complete with door shutter, frame, top fixed glass window, including all fittings, fixtures, hardware, fasteners and accessories, as per approved drawings, specifications and directions of Engineer- in-Charge.Door with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 12,373.00 |
| BMT-N.104.B | Providing and fixing in position factory- made Room entrance Steel door , complete with door shutter, frame, top fixed glass window, including all fittings, fixtures, hardware, fasteners and accessories, as per approved drawings, specifications and directions of Engineer- in-Charge.Door with above specifications, finished with polyester powder coating of minimum 60 microns and further sublimated using an approved Wood finish through dye- sublimation process, complete as per manufacturer’s specifications and as per direction of the Engineer-in-Charge | Sqm | 13,704.00 |
| BMT-N.104.C | Providing and fixing in position factory- made Room entrance Steel door , complete with door shutter, frame, top fixed glass window, including all fittings, fixtures, hardware, fasteners and accessories, as per approved drawings, specifications and directions of Engineer- in-Charge.Door with above specifications, finished with polyester powder coating of minimum 60 microns and further sublimated using an approved high-resolution image printed through dye-sublimation process, complete as per manufacturer’s specifications and as per direction of the Engineer-in-Charge | Sqm | 14,695.00 |
| BMT-N.105.A | Supply & Installation Galvanized Plain Skin Pass (GPSP) Door (Single/Double Shutter): Factory-made, single rebate Galvanized steel door (frame and shutter) for general applications, fabricated from Galvanized plain skin pass (GPSP) sheets conforming to IS 513 (D-quality) and IS 277 with 120 GSM zinc coating. Door Frame: Made from 1.0 mm thick GPSP sheet, roll-formed into a 100x78Door with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 13,302.00 |
| BMT-N.105.B | Supply & Installation Galvanized Plain Skin Pass (GPSP) Door (Single/Double Shutter): Factory-made, single rebate Galvanized steel door (frame and shutter) for general applications, fabricated from Galvanized plain skin pass (GPSP) sheets conforming to IS 513 (D-quality) and IS 277 with 120 GSM zinc coating. Door Frame: Made from 1.0 mm thick GPSP sheet, roll-formed into a 100x78Door with above specifications finished with polyester powder coating of minimum 60 microns and sublimated with approved wood finishes and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 14,635.00 |
| BMT-N.105.C | Supply & Installation Galvanized Plain Skin Pass (GPSP) Door (Single/Double Shutter): Factory-made, single rebate Galvanized steel door (frame and shutter) for general applications, fabricated from Galvanized plain skin pass (GPSP) sheets conforming to IS 513 (D-quality) and IS 277 with 120 GSM zinc coating. Door Frame: Made from 1.0 mm thick GPSP sheet, roll-formed into a 100x78Door with above specifications, finished with polyester powder coating of minimum 60 microns and further sublimated using an approved high-resolution image printed (Reflection Series Finish) through dye- sublimation process, complete as per manufacturer’s specifications and as per direction of the Engineer-in-Charge | Sqm | 15,910.00 |
| BMT-N.106.A | Supply & Installation Galvanized plain skin pass (GPSP) sheet closed box profile Door Frame only (Single Rebate – General Use) Suitable for 46mm shutter. Factory-made door frame constructed from 1.0 mm thick galvanized plain skin pass (GPSP) sheet (as per IS 513 'D' quality & IS 277 with 120 GSM zinc coating), roll-formed into a 100×78 mm single rebate closed-box profile with 20 mm decorative architrave. Frame is powder coated (pure polyester, 60–65 microns DFT), miter-cut, assembled with corner brackets and self-expanding screws. Internal cavity filled with Polyurethane Foam (PUF) of 32–36 kg/m³ density. Groove provided for EPDM gasket to ensure proper sealing with the shutter. Frame includes stiffeners for mounting hardware such as hinges, aldrop, tower bolt, door closer, etc. (hardware not included. stiffeners only). Hardware: 3 Nos. SS304 Ball Bearing Butt Hinges, All fasteners and screws in SS304 grade.Steel Door Frame with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Rmt | 1,281.00 |
| BMT-N.106.B | Supply & Installation Galvanized plain skin pass (GPSP) sheet closed box profile Door Frame only (Single Rebate – General Use) Suitable for 46mm shutter. Factory-made door frame constructed from 1.0 mm thick galvanized plain skin pass (GPSP) sheet (as per IS 513 'D' quality & IS 277 with 120 GSM zinc coating), roll-formed into a 100×78 mm single rebate closed-box profile with 20 mm decorative architrave. Frame is powder coated (pure polyester, 60–65 microns DFT), miter-cut, assembled with corner brackets and self-expanding screws. Internal cavity filled with Polyurethane Foam (PUF) of 32–36 kg/m³ density. Groove provided for EPDM gasket to ensure proper sealing with the shutter. Frame includes stiffeners for mounting hardware such as hinges, aldrop, tower bolt, door closer, etc. (hardware not included. stiffeners only). Hardware: 3 Nos. SS304 Ball Bearing Butt Hinges, All fasteners and screws in SS304 grade.Steel Door Frame with above specifications finished with polyester powder coating of minimum 60 microns and sublimated with approved wood finishes and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Rmt | 1,409.00 |
| BMT-N.107.A | Supply & Installation Galvanized plain skin pass (GPSP) Steel closed box profile Door Frame only (Single Rebate – General Applications): Suitable for 32/35mm shutter. Factory-made door frame from 1.0 mm thick GPSP sheet (IS 513 'D' quality, IS 277, 120 GSM zinc coated), powder coated with 60–65 microns DFT polyester finish. Roll-formed into 100×78 mm single rebate closed-box profile with 20 mm design architrave, suitable aluminium profile to receive 32–35 mm thick shutter. Frame is miter-cut, assembled with corner brackets and self-expanding screws. Filled with polyurethane foam (PUF) of 32–36 kg/m³ density. Includes groove for EPDM gasket for sealing and integrated stiffeners for fixing hardware (hinges, aldrop, tower bolt, etc.; hardware not included). Hardware: 3 Nos. SS304 Ball Bearing Butt Hinges, All screws and fasteners in SS304 grade.Steel Door Frame with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Rmt | 1,328.00 |
| BMT-N.107.B | Supply & Installation Galvanized plain skin pass (GPSP) Steel closed box profile Door Frame only (Single Rebate – General Applications): Suitable for 32/35mm shutter. Factory-made door frame from 1.0 mm thick GPSP sheet (IS 513 'D' quality, IS 277, 120 GSM zinc coated), powder coated with 60–65 microns DFT polyester finish. Roll-formed into 100×78 mm single rebate closed-box profile with 20 mm design architrave, suitable aluminium profile to receive 32–35 mm thick shutter. Frame is miter-cut, assembled with corner brackets and self-expanding screws. Filled with polyurethane foam (PUF) of 32–36 kg/m³ density. Includes groove for EPDM gasket for sealing and integrated stiffeners for fixing hardware (hinges, aldrop, tower bolt, etc.; hardware not included). Hardware: 3 Nos. SS304 Ball Bearing Butt Hinges, All screws and fasteners in SS304 grade.Steel Door Frame with above specifications finished with polyester powder coating of minimum 60 microns and sublimated with approved wood finishes and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Rmt | 1,459.00 |
| BMT-N.108.A | Factory-Supplied & Installed Single Rebate Galvanized Plain Skin Pass (GPSP) Door (Single/Double Shutter) with Vision Panel – Scientific Use: Constructed from Galvanized Plain Skin Pass (GPSP) sheets (as per IS 513 ‘D’ quality, IS 277 with 120 GSM zinc coating). Door Frame: Made from 1.0 mm thick GPSP sheet, roll-formed into a 100x78 mm closed box single rebate profile with 20 mm decorative architrave. Frame sections are mitered and assembled using corner brackets and self-expanding screws. Filled with PUF (32–36 kg/m³ density) and grooved to accommodate EPDM gasket for air-tight sealing. Door Shutter: 46 mm thick, fully flush double-skin shutter using 0.8 mm GPSP sheets, with lock-seam joints and U-shaped bent edges. Internal core filled with honeycomb kraft paper and stiffeners for hardware fitting. Vision Glass Panel: Fitted with double-Scientific door with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 13,303.00 |
| BMT-N.108.B | Factory-Supplied & Installed Single Rebate Galvanized Plain Skin Pass (GPSP) Door (Single/Double Shutter) with Vision Panel – Scientific Use: Constructed from Galvanized Plain Skin Pass (GPSP) sheets (as per IS 513 ‘D’ quality, IS 277 with 120 GSM zinc coating). Door Frame: Made from 1.0 mm thick GPSP sheet, roll-formed into a 100x78 mm closed box single rebate profile with 20 mm decorative architrave. Frame sections are mitered and assembled using corner brackets and self-expanding screws. Filled with PUF (32–36 kg/m³ density) and grooved to accommodate EPDM gasket for air-tight sealing. Door Shutter: 46 mm thick, fully flush double-skin shutter using 0.8 mm GPSP sheets, with lock-seam joints and U-shaped bent edges. Internal core filled with honeycomb kraft paper and stiffeners for hardware fitting. Vision Glass Panel: Fitted with double-Scientific door with above specifications finished with polyester powder coating of minimum 60 microns and sublimated with approved wood finishes and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 14,635.00 |
| BMT-N.109 | Supply & Installation Powder-Coated Lead-Lined Galvanized Plain Skin Pass (GPSP) Door (Single Rebate, Single Shutter – Open Profile frame): Factory-made door set with frame and shutter made from Galvanized plain skin pass (GPSP) sheet (as per IS 513 'D' quality, IS 277 with 120 GSM zinc coating). Door Frame: Made from 1.6 mm thick GPSP sheet, roll-formed to a 100×58 mm single rebate profile. Inner face of the frame is lined with 2.0 mm thick lead sheet and filled with PUF (32–36 kg/m³ density). Door Shutter: Constructed from 1.2 mm thick GPSP sheet to form a 46 mm thick fully flush, double skin shutter with lock- seam joints. Entire inner face is lead-lined with 2.0 mm thick lead sheet and filled with PUF (32–36 kg/m³ density). Finish: Factory-finished with pure polyester/epoxy-polyester/polyurethane powder coating (60–65 microns), in specified RAL colours. Hardware: 10" D-handle, Ball bearing butt hinges, Mortise dead lock, Concealed flush bolt, Door closer | Sqm | 17,761.00 |
| BMT-N.110.A | Supply & Installation of FD-120 Uninsulated Fire Rated Galvanized plain skin pass (GPSP) Shaft Door – 120-Minute Integrity (as per IS 3614:2021): Factory-made, single shutter, uninsulated fire-rated door set for non-egress areas (e.g., shafts), conforming to FD-120 classification under IS 3614:2021, tested as a complete assembly per IS 17518 (Part I). Door Frame: Made from 1.2 mm thick Galvanized plain skin pass (GPSP) sheet (zinc coating ≥120 GSM, IS 277), minimum 100×58 mm profile, mitred joints, reinforced for hardware, and grooved to accept fire- rated EPDM smoke seal, either inserted or adhered along the full perimeter. Door Shutter: 46 mm thick fully flush, double-skin construction from 1.2 mm GPSP sheets (≥120 GSM), with lock seamFire rated shaft door with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 14,755.00 |
| BMT-N.110.B | Supply & Installation of FD-120 Uninsulated Fire Rated Galvanized plain skin pass (GPSP) Shaft Door – 120-Minute Integrity (as per IS 3614:2021): Factory-made, single shutter, uninsulated fire-rated door set for non-egress areas (e.g., shafts), conforming to FD-120 classification under IS 3614:2021, tested as a complete assembly per IS 17518 (Part I). Door Frame: Made from 1.2 mm thick Galvanized plain skin pass (GPSP) sheet (zinc coating ≥120 GSM, IS 277), minimum 100×58 mm profile, mitred joints, reinforced for hardware, and grooved to accept fire- rated EPDM smoke seal, either inserted or adhered along the full perimeter. Door Shutter: 46 mm thick fully flush, double-skin construction from 1.2 mm GPSP sheets (≥120 GSM), with lock seamFire rated shaft door with above specifications finished with polyester powder coating of minimum 60 microns and sublimated with approved wood finishes and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 16,231.00 |
| BMT-N.111.A | Supply & Installation of BIS Certified FD- 120 Uninsulated Fire Rated Single Shutter GPSP sheet Door – 120-Minute Integrity (as per IS 3614:2021): Factory-supplied and installed door set for non-egress utility/service areas, tested as a complete assembly in accordance with IS 17518 (Part-I), conforming to IS 3614:2021 (FD- 120 classification – 120 minutes integrity). Door Frame: Made from 1.2 mm thick Galvanized plain skin pass (GPSP) sheet (min. 120 GSM zinc coating, IS 277), single rebate 100×58 mm profile, with mitred joints (self-tab/screwed at site), reinforced for hardware, and integrated groove for fire- rated EPDM smoke seal. Door Shutter: 46 mm thick double skin construction from 1.2 mm GPSP sheets (120 GSM), with lock seam joints, U-bent top/bottom edges, and resin-bonded honeycomb paper infill. Stiffened and pre- punched to receive hardware as per IS 16074. Vision Panel: Fitted with 120-minute fire- rated clear glass (min. 6 mm thick), max area 0.12 m², fixed using clip-on arrangement and fire-rated ceramic tape (2×13 mm) on both sides. Hardware: 1 fire-rated mortise dead lock,1 pair D-type pull handles,1 fire-rated heavy- duty surface door closer (Size 2–4, IS 3564 compliant, silver finish),SS ball bearing butt hinges (100×75×3 mm)Uninsulated Fire rated Door door with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 15,325.00 |
| BMT-N.111.B | Supply & Installation of BIS Certified FD- 120 Uninsulated Fire Rated Single Shutter GPSP sheet Door – 120-Minute Integrity (as per IS 3614:2021): Factory-supplied and installed door set for non-egress utility/service areas, tested as a complete assembly in accordance with IS 17518 (Part-I), conforming to IS 3614:2021 (FD- 120 classification – 120 minutes integrity). Door Frame: Made from 1.2 mm thick Galvanized plain skin pass (GPSP) sheet (min. 120 GSM zinc coating, IS 277), single rebate 100×58 mm profile, with mitred joints (self-tab/screwed at site), reinforced for hardware, and integrated groove for fire- rated EPDM smoke seal. Door Shutter: 46 mm thick double skin construction from 1.2 mm GPSP sheets (120 GSM), with lock seam joints, U-bent top/bottom edges, and resin-bonded honeycomb paper infill. Stiffened and pre- punched to receive hardware as per IS 16074. Vision Panel: Fitted with 120-minute fire- rated clear glass (min. 6 mm thick), max area 0.12 m², fixed using clip-on arrangement and fire-rated ceramic tape (2×13 mm) on both sides. Hardware: 1 fire-rated mortise dead lock,1 pair D-type pull handles,1 fire-rated heavy- duty surface door closer (Size 2–4, IS 3564 compliant, silver finish),SS ball bearing butt hinges (100×75×3 mm)Uninsulated Fire rated Door door with above specifications finished with polyester powder coating of minimum 60 microns and sublimated with approved wood finishes and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 16,861.00 |
| BMT-N.112.A | Supply & Installation of BIS Certified FD- 120 Partially Insulated Fire Rated Single Shutter GPSP sheet Door – 120 Min Integrity / 30 Min Insulation (IS 3614:2021): Factory-made fire door assembly for Staircases, Exit Routes, and Refuge Areas, tested as per IS 17518 (Part-I), conforming to FD-120 classification under IS 3614:2021, with 120 minutes integrity and 30 minutes insulation. Door Frame: Single rebate 100×58 mm profile made from 1.2 mm thick galvanized plain skin pass (GPSP) sheet (120 GSM, IS 277), with mitre-cut joints, site-assembled using self-tabs/screws. Frame includes groove for smoke seal or EPDM and reinforced to support hardware per IS 4351. Door Shutter: 46 mm thick double-skin galvanized steel construction (1.2 mm thick, 120 GSM), fully flush with lock seam joints and U-bent top/bottom edges. Shutter is internally filled with resin-bonded mineral wool or ceramic wool (96–120 kg/m³) with intumescent seal (min. 1.5×10 mm) on three edges of the door leaf and includes pre-punched slots and stiffeners as per IS 16074. Vision Panel: Fitted with 120-minute fire- rated 6 mm clear glass (max area: 0.06 m²), held with clip-on frame and ceramic tape (2×13 mm). Hardware: 1 Single-point panic device with external trim,1 heavy-duty overhead door closer (size 3–5, silver finish, IS 3564),SS ball bearing butt hinges (100×75×3 mm)Insulated fire rated door door with above specifications finished with polyester powder coating of minimum 60 microns of approved RAL colours and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 16,661.00 |
| BMT-N.112.B | Supply & Installation of BIS Certified FD- 120 Partially Insulated Fire Rated Single Shutter GPSP sheet Door – 120 Min Integrity / 30 Min Insulation (IS 3614:2021): Factory-made fire door assembly for Staircases, Exit Routes, and Refuge Areas, tested as per IS 17518 (Part-I), conforming to FD-120 classification under IS 3614:2021, with 120 minutes integrity and 30 minutes insulation. Door Frame: Single rebate 100×58 mm profile made from 1.2 mm thick galvanized plain skin pass (GPSP) sheet (120 GSM, IS 277), with mitre-cut joints, site-assembled using self-tabs/screws. Frame includes groove for smoke seal or EPDM and reinforced to support hardware per IS 4351. Door Shutter: 46 mm thick double-skin galvanized steel construction (1.2 mm thick, 120 GSM), fully flush with lock seam joints and U-bent top/bottom edges. Shutter is internally filled with resin-bonded mineral wool or ceramic wool (96–120 kg/m³) with intumescent seal (min. 1.5×10 mm) on three edges of the door leaf and includes pre-punched slots and stiffeners as per IS 16074. Vision Panel: Fitted with 120-minute fire- rated 6 mm clear glass (max area: 0.06 m²), held with clip-on frame and ceramic tape (2×13 mm). Hardware: 1 Single-point panic device with external trim,1 heavy-duty overhead door closer (size 3–5, silver finish, IS 3564),SS ball bearing butt hinges (100×75×3 mm)Insulated fire rated door door with above specifications finished with polyester powder coating of minimum 60 microns and sublimated with approved wood finishes and shades all complete as per manufacturer's specifications and as per direction of the Engineer-in-charge | Sqm | 18,327.00 |
Other chapters in this schedule
- Bricks & Building Blocks (21)
- Natural Flooring Stones (23)
- Wall & Floor Tiles (40)
- Paving & Interlocking Tiles (25)
- Timber & Roofing Materials (23)
- Steel Materials (26)
- Fixtures for Doors & Windows (103)
- Construction Chemicals & Admixtures (89)
- Glass Materials (21)
- Paints & Polishes (42)
- Particle Boards (110)
- Plywoods, Laminates & Veneers (31)
- Ceilings, Wall Partitions & Wall Linings (103)
- Windows (99)
- Structural Glazing & Curtain Walling (6)
- Dismantling (13)
- Expansion Joint Fillers (11)
- Miscellaneous Items (305)
- Expansion Joints (6)
- Energy Efficient Items (33)
- S.W.G. Pipes & Fittings (62)
- Man Holes & Inspection Chambers as per IS 4111 : Part 1 : 1986 (6)
- C.I. Pipes & Fittings as per IS 1729:1979 (41)
- Vitreous Chinaware Sanitary Appliances as per IS:2556 – 1974 (39)
- Taps & Faucets (6)
- G.I. Pipes & Fittings (15)
- PVC Pipes & Fittings (26)
- M.S. Conduit Pipes (51)
- PVC Conduits (36)
- Hot Dip Galvanized Metal Boxes for Switch Boards (9)
- T.W. Boards (25)
- Copper Flexible Cables (as per IS:694) (66)
- Service Mains and Flat Cable for Submersible Motors (16)
- Flush Type Switches and Accessories (27)
- Modular Switches and Accessories (49)
- Panel Mounting Switch Disconnector Fuse Units (sdfu) (10)
- On Load Changeover Switches (open Execution) (10)
- Auto Transfer Switch (14)
- Rewirable / Double Break Switches in SS Enclosure (12)
- Hrc Fuse Links (DIN/BOLTED Type) (6)
- Porcelain Rewirable Fuse Units (6)
- Panel Mounting MCCBs (113)
- MCBs (as per IS:60898-1:2002) (23)
- Isolators Confirms to I E C 60947 PART-III (22)
- RCCBs (ELCB/RCD) Confirms to IEC:61008 and IS:12640-1 (22)
- MCB Distribution Boards (as per IS 8623; IS 13032; Iec 61439-3) (44)
- Automatic Street Light Control Systems (12)
- Flourscent Tubes / CFL Lamps / LED Bulbs (5)
- LED Luminaires Indoor (74)
- U.G. Cables (135)
- Cable Trays (19)
- Double Walled Corrugated HDPE Pipe (8)
- Fans (18)
- Water Heaters (conventional & Solar) (14)
- Accessories for Water Heaters (11)
- Pumpsets (96)
- Air Conditioners (15)
- HVAC SYSTEMS(VRV/VRF) (70)
- Stabilizers (10)
- Repairing of Fans, Coolers, Pumps, Motors, Fridges and Airconditioners (76)
- Swaged / Octagonal Poles and Garden Posts (49)
- LT Panel and Accessories (33)
- Sub Station Equipment and Transformers (18)
- Maintenance and Repairs of Transformers (21)
- Overhead Lines& Line Materials (27)
- Lightening Protective System (16)
- Earthing (19)
- Local Area Network (59)
- Raceways and Junction Boxes (9)
- Computers, Printers and Scanners (16)
- Small System (7)
- Large EPABX System (16)
- C.C.TV & Surveillance System (16)
- Public Address Systems (15)
- AUDIO-VIDEO Systems (32)
- Legend Plates (8)
- Copper / Aluminium / G.I. Items (per Kg) (6)
- SMC Type Supports for the Busbars (36)
- Addressable - Fire Alarm System (27)
- Conventional - Fire Alarm System (14)
- Powder Based Fire Extinguishers (18)
- Fire Hydrant and Sprinkler System (58)
- Generators Specification (7)
- Inverters and Online UPS Systems (34)
- Temporary Illumination (57)
- Lifts (new Installation) (9)
- Medical Gas Pipeline System (10)
- Building Management Systems (21)
Pricing doors, shutters & frames against a live tender
Mapping a tender BOQ to the right schedule items, applying the current cost index, and catching where rates have moved since the base edition is slow and easy to get wrong. Arched's estimation engine reads the tender, maps it to the applicable schedule, and flags where the numbers are exposed before submission.
See how estimation works