Chhattisgarh SOR 2026
Roofing and Ceiling rates
77 roofing and ceiling items from the Chhattisgarh Public Works Department (PWD), effective 2026-06-10.
Roofing and Ceiling rates in the Chhattisgarh Building Schedule of Rates 2026 run from ₹4.00 to ₹8,398.00. Transcribed from Chhattisgarh PWD — Modified Building SOR, 10 June 2026. Reference only — verify against the official source before pricing a bid.
/
77 items — scroll the table to browse
| Description | Unit | ||
|---|---|---|---|
| 10.4.2 | Extra for making opening or recesses in C.G.I. sheets roofing of girth not more than 1 metre.Above 100 sq.cm. upto 400 sq.cm | Each | 40.00 |
| 10.4.3 | Extra for making opening or recesses in C.G.I. sheets roofing of girth not more than 1 metre.Above 400 sq.cm. in area | Each | 63.00 |
| 10.6 | Providing valley of 90cm overall width in plain G.I. sheet 1.6 mm thick with zinc coating not less than 350gm/sqm fixed with galvanized iron J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete | Metre | 895.00 |
| 10.7.1 | Providing and flashing 38cm. over all width in plain G.I. sheet fixed, with galvanized iron J or L hooks bolts and nuts G.I. limpet washers and fixed in walls with cement mortar 1:3 (1 cement: 3 sand)G.I. plain sheet 1.25mm thick (weight 10.56 kg/m2) | Metre | 357.00 |
| 10.7.2 | Providing and flashing 38cm. over all width in plain G.I. sheet fixed, with galvanized iron J or L hooks bolts and nuts G.I. limpet washers and fixed in walls with cement mortar 1:3 (1 cement: 3 sand)G.I. plain sheet 1.00 mm thick (weight 8.60 kg/m2) | Metre | 319.00 |
| 10.10 | Extra for providing and fixing wind ties of 40x6mm flat iron section | Metre | 100.00 |
| 10.11 | Supply and fixing of precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required | Sqm | 541.00 |
| 10.12 | Supply and fixing of polymer precoated galvalume profile sheets (PPGL) of approved size, shape and pitch of corrugation, total coated thickness (TCT) 0.60 mm +/- 5%, epoxy primer on both side of the sheet and colour polyester top coat 18-20 microns and 6-7 microns on bottom. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required | Sqm | 589.00 |
| 10.13 | Supply and fixing of precoated TILE PATTERN profile sheets of approved make, colour, over all size, corrugation shape and pitch, having total coated thickness (TCT) 0.45 mm (approx weight 4.9 kg/sqm) with Zn-Al coating and superior paint and having yeild strength of 550 MPa. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required | Sqm | 801.00 |
| 10.14 | Providing and fixing 2mm thick semi transparent polycarbonate profile roofing sheet of approved make and colour to make any normal roofing / covering and fixing as per manufacture specification at spacing not more than 1.2 m centre to centre with EPDM gasket and silicon sealant fixed with self drilling stainless steel screws all complete as per direction of Engineer-in-Charge | Sqm | 1,615.00 |
| 10.15 | Extra for working height above 6 metre for fixing GI/ profile/ PVC/ polycarbonate sheet for every additional height of 1 metre of part thereof | Sqm | 4.00 |
| 10.16.1 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete:Ridges plain (500-600mm) | Metre | 469.00 |
| 10.16.2 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete:Flashings/ Aprons. (Upto 600 mm) | Metre | 458.00 |
| 10.16.3 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete:North light curves | Metre | 490.00 |
| 10.16.4 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete:Barge board (Upto 300 mm) | Metre | 413.00 |
| 10.16.6 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete:Gutter. (600 mm over all girth) | Metre | 535.00 |
| 10.17 | Providing asbestos cement 6mm thick corrugated or semi corrugated sheets roofing fixed with galvanized J or L hooks, bolts and nuts 8mm dia G.I. plain bitumen washers complete excluding the cost of purlins, rafters and trusses | Sqm | 295.00 |
| 10.18 | Extra for asbestos cement corrugated/semi corrugated sheet roofing with vertical sheeting or sheeting to pitch exceeding 60 degree | Sqm | 43.00 |
| 10.19 | Extra for straight cutting in asbestos cement corrugated/ semi corrugated sheet roofing for making opening of area exceeding 0.40 sqm. for chimney stacks, sky light etc | Metre | 37.00 |
| 10.20 | Extra for racking or circular cutting in A.C. corrugated/ semi corrugated sheet roofing | Metre | 49.00 |
| 10.21.1 | Extra for making opening or recesses in asbestos cement corrugated/ semi corrugated sheet roofing of girth not more than 1 metre:Not exceeding 100 sq.cm. in area | Each | 33.00 |
| 10.21.2 | Extra for making opening or recesses in asbestos cement corrugated/ semi corrugated sheet roofing of girth not more than 1 metre:Exceeding 100 sq.cm but not exceeding 400 sq.cm in area | Each | 56.00 |
| 10.21.3 | Extra for making opening or recesses in asbestos cement corrugated/ semi corrugated sheet roofing of girth not more than 1 metre:Exceeding 400 sq.cm. in area | Each | 79.00 |
| 10.22.1 | Providing and fixing ridges and hips in asbestos cement sheet roofing with G.I., J or hooks, bolts and nuts 8 mm dia, G.I plain and bitumen washers complete.Plain angular ridges | Metre | 46.00 |
| 10.22.2 | Providing and fixing ridges and hips in asbestos cement sheet roofing with G.I., J or hooks, bolts and nuts 8 mm dia, G.I plain and bitumen washers complete.Serrated or plain wing adjustable ridges | Metre | 56.00 |
| 10.23.1 | Providing and fixing asbestos cement roofing accessories with galvanized iron J or L hooks, bolts and nuts and/or G.I. seam bolts & nuts, G.I. plain & bitumen washers etc. complete.Apron flashing pieces | Metre | 62.00 |
| 10.23.2 | Providing and fixing asbestos cement roofing accessories with galvanized iron J or L hooks, bolts and nuts and/or G.I. seam bolts & nuts, G.I. plain & bitumen washers etc. complete.Eaves filler pieces | Metre | 85.00 |
| 10.23.3 | Providing and fixing asbestos cement roofing accessories with galvanized iron J or L hooks, bolts and nuts and/or G.I. seam bolts & nuts, G.I. plain & bitumen washers etc. complete.North light and ventilator curves | Metre | 90.00 |
| 10.30.1 | Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately).Natural colour insulating board | Sqm | 106.00 |
| 10.30.2 | Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately).White face insulating board | Sqm | 359.00 |
| 10.30.3 | Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately).Flame retardant face insulating board | Sqm | 324.00 |
| 10.31.1 | Providing and fixing 18mm thick insulating board ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately).Natural colour insulating board | Sqm | 343.00 |
| 10.31.2 | Providing and fixing 18mm thick insulating board ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately).White face insulating board | Sqm | 415.00 |
| 10.31.3 | Providing and fixing 18mm thick insulating board ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately).Flame retardant face insulating board | Sqm | 380.00 |
| 10.32.1 | Providing and fixing 3 mm thick hard board sheet ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately).Standard Quality Board | Sqm | 206.00 |
| 10.33.1 | Providing and fixing 4.5mm thick hard board sheet ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately).Standard Quality Board | Sqm | 225.00 |
| 10.34.1 | Extra for circular cutting in ceiling with.Teak wood planks 20 mm thick | Metre | 24.00 |
| 10.34.2 | Extra for circular cutting in ceiling with.Other than teak wood (Sal, Bija, Haldu) | Metre | 28.00 |
| 10.34.3 | Extra for circular cutting in ceiling with.Insulating board 12 mm thick | Metre | 17.00 |
| 10.34.4 | Extra for circular cutting in ceiling with.Insulating board 18 mm thick | Metre | 20.00 |
| 10.34.5 | Extra for circular cutting in ceiling with.Hard board 3 mm thick | Metre | 11.00 |
| 10.34.6 | Extra for circular cutting in ceiling with.Hard board 4.5 mm thick | Metre | 13.00 |
| 10.36 | Extra for making chamfered edges of beading | Metre | 5.00 |
| 10.37 | Extra for providing and fixing ceiling to curved surface in narrow width | Sqm | 78.00 |
| 10.38 | Providing and laying split (half cut) 25mm dia bamboo jaffree 150mm mesh including tying to the purlins and rafters with moonj ban or string complete | Sqm | 115.00 |
| 10.39 | Providing and laying non-modular brick tiles of class designation 3.5 over mumty roofs grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over a 12 mm layer of cement mortar 1:3 (1 cement: 3 fine sand) and finished neat | Sqm | 212.00 |
| 10.40 | Painting top of roofs with bitumen of approved quality @ 17kg/10Sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete | Sqm | 80.00 |
| 10.41 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10mm and down grade) including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design | Metre | 58.00 |
| 10.42 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx650 micron thick (0.65mm), finished with 12mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete | Each | 174.00 |
| 10.43 | Providing and laying single wheel tilling without batten | Sqm | 290.00 |
| 10.44 | Providing and laying single wheel tiling over and including half split (splitted into 2 pieces) bamboo batten 50 to 70 mm at a distance of 200mm both side | Sqm | 735.00 |
| 10.45 | Providing and laying single wheel tiling over and including whole bamboo batten 50 to 70 mm at a distance of 200mm both side | Sqm | 847.00 |
| 10.46 | Providing and laying Manglore pattern tiles 20 mm thick (without hip or ridge tiles) on steel/ wooden frame (frame work to be paid separately) | Sqm | 503.00 |
| 10.47 | Providing and laying Manglore pattern hips and ridge tiles fixed in cement mortar 1:6 etc. complete | Metre | 111.00 |
| 10.48 | Providing and fixing Terracota tiles of approved design and size over and including 20mm thick cement plaster 1:3 including floating coat of cement slurry on bed and filling joints with neat cement slurry mixed with pigment to match the shade of tiles complete | Sqm | 447.00 |
| 10.49 | Providing and fixing ISI Marked designer tiles of approved design and size confirming to IS: 13801 over and including 20mm thick cement plaster 1:3 including floating coat of cement slurry on bed and filling joints with neat cement slurry mixed with pigment to match the shade of tiles complete | Sqm | 852.00 |
| 10.50 | Providing and fixing 100 mm diameter and 60 cm long stone ware rain water spout in cement mortar 1:4 (1 cement: 4 fine sand) | Each | 52.00 |
| 10.51 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 150mm diameter and weighing not less than 440 grams | Each | 48.00 |
| 10.54 | Extra for sunk or raised mouldings in the Gypsum board/ plaster of paris false ceiling | Sqm | 157.00 |
| 10.55 | Extra for providing plaster of paris (Gypsum and anhydrous) with ceiling above 5 m height from floor level | Sqm | 44.00 |
| 10.56 | Providing and fixing 12mm thick plaster of paris (Gypsum Anhydrous) with ceiling upto a height of 5 M. above floor level over wooden frame and rendering smooth with plaster of paris (Frame work to be paid separately) | Sqm | 162.00 |
| 10.57 | Extra for providing and fixing ceiling to curved surfaces in narrow width | Metre | 78.00 |
| 10.58 | Extra for providing 3 mm thick translucent white acrylic plastic sheets of approved quality in false ceiling instead of 12 mm thick plain/or with design particle board ceiling tiles in item above | Sqm | 388.00 |
| 10.59 | Providing and fixing steel frame work for partition wall made from steel rectangular tube of 50x25mmx1.25mm (wall thickness) with welded joints complete with grinding the welded joints. The members of the frame work along the wall/floor/ceiling shall form a grid of not more than 1100mmx1100mm centre to centre of member in any direction and are to be screwed using 75x10 mm wood screws to the prefixed wooden plugs at an interval of not more than 500mm centre to center. The vertical members to be grouted in the floor upto 50mm deep including repairing of wall/floor/ceiling with 1:3 Cement mortar | KG | 80.00 |
| 10.60 | Providing and fixing steel grid for false ceiling made from M.S. rectangular hollow tubes of 50x25x1.25mm (wall thickness) as main runners to be jointed to cross runners of same size by electric arc welding with spacing not exceeding 610x610mm in any direction. The frame to be screwed to the wall using wooden plugs and wood screws of size 50x8mm at an interval of not more than 300mm centre to centre. The grid to be supported using 6mm M.S. hanger bars at 1200mm centre to centre both ways bent, hooked, fixed to existing R.C.C. roof with fastner or to the truss as the case may be and bolted to the grid with the help of suitable M.S. holding cleats, complete | KG | 86.00 |
| 10.61 | Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting | Sqm | 559.00 |
| 10.62 | Providing and fixing Gypsum board wall paneling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of G.I. section,'W' profile (0.55mm thick ) having a knurled web of 51.55mm and two flanges of 26mm each with lips of 10.5 mm placed at 610mm center to center in perimeter channel having one flange of 20mm and another flange of 30mm with thickness of 0.55mm and web of length 27mm fixed on the floor and the ceiling with the nylon sleeves with fully threaded self-tapping drive all screws, and 12.5mm Gypsum board conforming to IS: 2095 - 1996: Part - I, fixed to 'W' profile with 25 mm countersunk ribbed head screws at 200mm center to center, joints of the boards are finished with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish all complete as per the drawing & directions of Engineer-in- charge | Sqm | 472.00 |
| 10.63 | Providing and fixing 97mm thick Gypsum board partition upto ceiling height consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120, consisting of floor and ceiling channel 50mm wide having equal flanges of 32mm and 0.55mm thick fixed to the floor and ceiling at the spacing of 610mm centre to centre with dash fastener of 12.5mm diameter 40mm length and the studs 48mm wide having one flange of 34mm and other flange 36mm and 0.55mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6mm dia bolts and nuts at both ends of partition fixed flush to wall with rawl plugs at spacing of 450mm centre to centre and fixing of boards to either side of frame work by 25mm dry wall screws on studs, floor and ceiling channels at the spacing of 300mm centre to center and 97mm thick Gypsum board which includes one layer of tapered edge 12.5mm thick Gypsum plaster board (conforming I.S. 2095-1982) screw fixed with 25mm screws at 300mm centre to centre to either side, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, joint finisher and two coats of primer suitable for board as per manufacture's specification and Direction of Engineer-in-charge all complete | Sqm | 644.00 |
| 10.69 | Providing and fixing false ceiling at all heights with 15 mm thick integral densified tegular edged light weight calcium silicate false ceiling tile reinforced with fibre and natural filler false ceiling tiles of Size 595x595 MM of approved texture, design and patterns (such as cosmos, spinton, quatra, golb) having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 & 7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum. in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 40 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. Ceiling height up 3.5 mt from adjacent floor level.Extra height to be paid separately | Sqm | 1,239.00 |
| 10.70 | Providing and fixing false ceiling at all heights with 15 mm thick integral densified Microlook tegular edged light weight calcium silicate false ceiling tile reinforced with fibre and natural filler false ceiling tiles of Size 595x595 MM of approved texture, design and patterns (such as cosmos, spinton, quatra, golb) having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 & 7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0 KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette gride, rotary stiched double webbed white with 6 mm reveal profile (white/black), comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 40 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. Ceiling height up 3.5 mt from adjacent floor level.Extra height to be paid separately | Sqm | 1,431.00 |
| 10.71 | Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0 KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum, comprising of a frame made from especiallyfabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600 mm centers using 12mm dia, 40mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete. Ceiling height up 3.5 mt from adjacent floor level. Extra height to be paid separately | Sqm | 1,726.00 |
| 10.72 | Extra for additional height every 1m or part thereof where height of false ceiling work exceeds 3.5 metre from the floor under consideration for necessary scaffolding with adequate bracing, propping etc at all level of floor for all type of ceiling.Extra height shall be considered from adjacent floor to finished bottom level of false ceiling. (only plan area is to be measured) | Sqm | 44.00 |
| 10.73 | Supply & installation of Slats wall panelling made of E 1 grade laminated/melamine High Density Fiber board having minimum density 800kg/ cum i.e. 12.8kg/m2 16mm thick board which having grove perforated slats L 24-4 -(Router Machine cut 4mm groves @24mm pitch with 9.8% open area ) in size 192x2440x16 mm slats/planks with tongue & groove edge of a seamless look. This slats/plank having acoustical fleeces of 0.27mm thick surface density of fleeces 63g/m2. This planks are erect on wall with proper manner & finish as per drawing with back line acoustic synthetic poly fiber 1000 gsm 50mm thick with G.I wire mesh in the framing channel.This framing channel are galvanised channel 50x50x100 thickness 0.45 mm of @ 600mm c/c and cross channel 18x27x21 thickness 0.5 mm @ 400mm c/c with required fastener to the wall. This slat/planks are to be fixed in a manner having 3 mm expansion joint between 4.88m length & 5.00 m in vertical direction.This all system should confirms Fire rating class B, Acoustics of material should not less than Noise Reduction Coefficient of 0.8 & sustain in climate condition(C, RH)- Minimuam 50. All, products having green eco-friendly material should confirm low V.O.C of grade E- l & R.E %-25. All work complete upto Height of 15.00 Mt. Cost of scaffolding to be paid separately { make anutone, ecotone acoustic, himalyan acoustics, saint gobain Gyproc.) | Sqm | 7,908.00 |
| 10.74 | Supply and installation of Stretch fabric with Noise Reduction Coefficient and polyester core, digitally printed/ non printed acoustically, transparent face covering of choice colour, width of fabric1.4m (Minimum 100mm additional fabric is required for tucking hence maximum module wall fabric width would be l300mm). in ceiling/wall surface, combination of Wood fiber board minimum density 400 Kg/cum weight 4Kg/sqm 600x1200x l0mm, Synthetic poly fiber 1000 GSM and 25mm thick infill with Suitable framework of approx 50x50x100 channel at every 600mm C/C. First framework on wall to be erected so as to achieve desired profile and finish level as per dwg. This board fastened perpendicular to fixed framework with suitable fasteners. Suitable gripper fixed on Wood fibre board with metal fasteners as per marking lines for fixing plastic sleeves. Synthetic poly fiber 1000 GSM and 25mm thick is then adhered, in between tracks, using adhesive. The Stretch acoustical fabric of width 1.4m is stretched and tucked into the Tracks and secured to the locking jaws with propose- specific tucking tools to obtain smooth, taut, wrinkle-free finish. Ensure the weft and weave of the fabric along with the surface all oriented in one direction to achieve uniform shade as per the drawing including all tools tackels and specialised supervision including cad cam shop drawing for accuracy of workmanship. Fabric System should be fire retardant as per IS 15061-2002. All work complete upto Height of 15.00 Mt. Cost of scaffolding to be paid separately { make anutone, ecotone acoustic, himalyan acoustics, saint gobain Gyproc.} | Sqm | 8,398.00 |
| 10.75 | Supply and installation of Plane Stretch fabric with Noise Reduction Coefficient and polyester core, acoustical fabric, transparent face covering of choice colour, width of fabric1.4m (Minimum 100mm additional fabric is required for tucking hence maximum module wall fabric width would be l300mm). in ceiling/wall surface, combination of Wood fiber board minimum density 400 Kg cum weight 4Kg/sqm 600x1200xl0mm, Synthetic poly fiber 1000 GSM and 25mm thick infill with Suitable framework of approx 50x50x 100 channel at every 600mm C/C. First framework on wall to be erected so as to achieve desired profile and finish level as per dwg. This board fastened perpendicular to fixed framework with suitable fasteners. Suitable gripped fixed on Wood fibre board with metal fasteners as per marking lines for fixing plastic sleeves. Synthetic poly fiber 1000 GSM and 25mm thick is then adhered, inbetween tracks, using adhesive. The Stretch acoustical fabric of width 1.4m is stretched and tucked into the Tracks and secured to the locking jaws with propose- specific tucking tools to obtain smooth, taut, wrinkle-free finish. Ensure the weft and weave of the fabric along with the surface all oriented in one direction to achieve uniform shade as per the drawing including all tools tackels and specialised supervision including cad cam shop drawing for accuracy of workmanship. Fabric System should be fire retardant as per IS 15061-2002. All work complete upto Height of 15.00 Mt. Cost of scaffolding to be paid separately ( make anutone, ecotone acoustic, himalyan acoustics, saint gobain Gyproc.} | Sqm | 7,678.00 |
| 10.77 | SupplyandInstallationofperforatedGlassFiber Reinforced gypsum panel, back/ined with acoustical fleece, having 3x3mm square perforations @ 8.33mm pitch with - 8 % open area, size 1200x2400x12.5mm tapered long edges, volume density of base board 700 Kgs/cum, weight of board 9Kg/m2installed by using suitable channel system ceiling framework. The Strut ceiling framework system shall include GI channel,fully knurled,sectional thickness 0.50mm, length 3600mm, unequal flanges and web of 25mm,fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centers. The GI channel 0.9mm thickness, fully knurled,sectional thickness 0.8mm,length 3600mm. equal flanges of 15mm and web 45mm from the soffit at l200mm centers with channel, fully knurled, Suspender angle with sectional thickness 0.45mm, unequal flanges of 25 & 10mm such that free end of GI channel rests on GI channel along perimeter of ceiling. Extra support to be added on per requirement. more than l50mm. GI channel fully knurled, sectional thickness 0.55mm,length 3600mm,web 50mm,depth of 25mm and equal flanges 15mm is fastened to the GI channel perpendicularly at 600mm centers with other suitable GI channel members to hold board in proper position with adequate strength panel is installed on the GI channel with suitable fasteners at 600/400/300mm centres. The tapered long edges are then filled and finished with Seam AIC and tape. The short square edges are also similarly finished but no tape. Apply one coat of white primer with roller brush evenly across the Pixel surface to achieve uniform colour. The system is backlined with the acoustical infill Synth PF 10x50. All work complete upto Height of 15.00 Mt. Cost of scaffolding to be paid separately { make anutone, ecotone acoustic, himalyan acoustics, saint gobain Gyproc.} | Sqm | 3,885.00 |
| 10.78 | Supply and Installation of acoustical texture panel for ceiling and wall with square edge, Glassfibre core fully special fiture as per dwg.ceiling tile of size 595x595x15 mm havingvolumedensity120Kg/cum,weight1.8kg/m2 suspended using 0.3 mm thick GI channel frame work T24 metal grid system. Skelet TrelisT24 ceiling grid system of 600x600mmmoduleincludesappropriate,sectionof thickness 0.4mm, with equal flanges of 24mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then appropriate section suspend on the sectional thickness 0.3mm,with flange width 24mm,height 38mm and length 3600mm,from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at l200mm centres. appropriate section of thickness 0.3mm,with flange width 24mm, height 32mm and length l200mm is interlocked into the pre-cut slots in the Main section at 600mm centers in the perpendiculardirectionto the Main section.Finally, sectional thickness 0.3mm, with flange width 24mm, height 32mm and length 600mm are interlocked into the precut slots in the CrossT in direction parallel to the Main section to result in 600x600mm module. acoustical texture panel. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade.All work complete upto Height of 15.00 Mt. Cost of scaffolding to be paid separately (make anutone, ecotone acoustic, himalyan, acoustics, saint gobain Gyproc.) | Sqm | 4,835.00 |
Other chapters in this schedule
- Earth Work (46)
- Form Work (20)
- Cement Concrete (Plain and Reinforced) (24)
- Water Proofing (25)
- Stone Work (12)
- Brick Work (44)
- Wood and PVC Work (128)
- Steel and Aluminium Work (73)
- Plastering and Pointing (52)
- Flooring (87)
- Marble & Stone Wall Lining Work (24)
- Distempering, Painting and Finishing (57)
- Dismantling and Demolishing (53)
- Repair to Buildings (49)
- Sanitary Installations (64)
- Water Supply (64)
- Drainage (48)
- Tube Well & Rain Water Harvesting (8)
- Horticulture & Landscaping (32)
- Fire Fighting (30)
- Miscellaneous (8)
Pricing roofing and ceiling against a live tender
Mapping a tender BOQ to the right schedule items, applying the current cost index, and catching where rates have moved since the base edition is slow and easy to get wrong. Arched's estimation engine reads the tender, maps it to the applicable schedule, and flags where the numbers are exposed before submission.
See how estimation works