Tripura SOR 2023
Steel Work rates
43 steel work items from the Tripura PWD (R&B and Buildings), effective 2023-04-01.
Steel Work rates in the Tripura Building Schedule of Rates 2023 run from ₹60.90 to ₹8,166.80. Transcribed from Tripura PWD — SoR 2023: Building Works, basic rates as on or just before 01.04.2023. Reference only — verify against the official source before pricing a bid.
/
43 items — scroll the table to browse
| Description | Unit | ||
|---|---|---|---|
| 9 | Concrete in driven cast-in-situ piles shall be cast minimum above the designed top level of pile, which shall be stripped either before final set or after 3 days. Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap): 400 mm dia piles. 450 mm dia piles. 500 mm dia piles. 550 mm dia piles. 600 mm dia piles. 750 mm dia piles. Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct Mud Circulation (DMC) or Bailer and Chisel Technique by Tripod and Mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads. (Length of pile for payment shall be measured upto bottom of pile cap). Note: Truck Mounted rotary / TMR / Tubewell Boring Machine shall not be used. 450 mm dia piles. 500 mm dia piles. 550 mm dia piles. 600 mm dia piles. 750 mm dia piles. Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler Mounted, telescopic boom hydraulic piling Rig all complete, including removal of excavated earth with all its lifts and leads. (Length of pile for payment shall be measured upto bottom of pile cap). Note: Truck Mounted rotary / TMR / Tubewell Boring Machine shall not be used. 600 mm dia piles. 750 mm dia piles. 1000 mm dia piles. 1200 mm dia piles. 1500 mm dia piles. Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete as per specification & the direction of Engineer incharge (Length of pile for payment shall be measured upto to the bottom of pile cap):- 300 mm dia piles. 400 mm dia piles. 450 mm dia piles. 500 mm dia piles. 550 mm dia piles. Extra over item No. 15.4 for boring, providing and installing cast-in-situ additional bulb in under reamed reinforced cement concrete piles, under specified dia meter as per specification & the direction of Engineer incharge (only the quantity of extra bulbs are to be paid):- 300 mm dia piles. 400 mm dia piles. 450 mm dia piles. 500 mm dia piles. 550 mm dia piles. Providing, driving (with vibrating pile driving hammer complete with power units & accessories) and installing driven Pre-cast reinforced cement concrete piles of specified diameter and length below the pile cap in M25 cement concrete to carry safe working load not less than specified with a central through preformed hole with M.S. black pipe of dia. 40mm for grouting with cement sand grouting of mix 1:2 (1 cement: 2 fine sand) under sufficient positive pressure to ensure complete filling including centring, shuttering, driving and removing the steel casing pipe and lifting casing etc. complete but excluding the cost of steel reinforcement as per specification & the direction of Engineer incharge (Length of pile for payment shall be measured from top of the shoe to the bottom of pile cap):- 400 mm dia piles. 450 mm dia piles. 500 mm dia piles. 550 mm dia piles. 600 mm dia piles. 750 mm dia piles. Vertical load testing of piles in accordance with 2911 (Part IV) including installation of loading platform by Kentledge and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer incharge:- Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic Method of Testing Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in- Charge. Single pile upto 50 tonne safe capacity Initial test (Test Load 2.5 times the safe Capacity). Routine test (Test Load 1.5 times the safe Capacity). Single pile above 50 tonne and upto 100 tonne safe capacity pile:- Initial test (Test Load 2.5 times the safe Capacity). Routine test (Test Load 1.5 times the safe Capacity). Group of two or more piles upto 50 tonne safe capacity Initial test (Test Load 2.5 times the safe Capacity). Routine test (Test Load 1.5 times the safe Capacity). Cyclic vertical load testing of pile in accordance with IS Code of practice IS: 2911 (part IV) by Kentledge method including preparation of pile head etc. for. Single Pile:- Upto 50 tonne Safe capacity pile. Above 50 tonne and upto 100 tonne Safe capacity pile. Group of two or more piles:- Upto 400 tonne safe capacity pile of group Lateral load testing of single pile in accordance with IS Code of practice IS: 2911 (Part IV) for determining safe allowable lateral load on pile as per specification & the direction of Engineer incharge:- Upto 50 tonne capacity pile. Above 50 tonne and upto 100 tonne capacity pile. Integrity testing of Pile using Low Strain / Sonic Integrity / Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top bt removing soil, mud, dust and chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test and submission of results, all complete as per direction of Engineering-in-Charge. Note: The inclusion of the above item in the schedule of work shall judiciosly decided by the technical sanctioning authority, keeping in view the quality control, type of soil strata and importance of the project. Bandhani Carpenter 1st class Carpenter 2nd class Beldar Fitter (grade 1) Glazier Mason (brick layer) 2nd class Mate Skilled Beldar (for floor rubbing etc.) Mason (average) Helper Chromium plated Brass screws 20 mm Galvanised steel plain sheets Float glass sheet of nominal thickness 4 mm (weight not less than 10kg/sqm). Float glass sheet of nominal thickness 5.5 mm.(weight not less than 13.50 kg/sqm). Brass 100mm mortice latch and lock with 6 levers without pair of handles Dash fastener/ Chemical fastener Rawl plug 50 mm (designation 10 no.) Aluminium T or L sections Expandable fastener with plastic sleeve and M.S. screws. 32 mm long Cadmium plated full threaded steel screws (30x4 mm dia.) Aluminium washer 2 mm thick 15 mm dia Dash hold fastener 12.5 mm dia, 50 mm long with 6 mm dia bolt Anodising 15 microns on aluminium sections kilogram Neoprene/EPDM rubber gasket Anodising 25 microns on aluminium sections kilogram Powder coating 50 microns on aluminium sections. Polyester powder coating 50 microns on aluminium sections Double action hydraulic floor spring with stainless steel cover plate 6 mm dia. G.I. adjustable hangers including clips (up to 1.2 m length) Double action hydraulic floor spring with brass cover plate Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS: 12823 (exterior grade)12 mm thick Prelaminated particle board with both sides decorative lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS: 12823 (exterior grade)12 mm thick Silicon sealant. cartridge Stainless steal screws 30mm x4mm. Hermetically sealed double glazed unit made with 6mm thick clear float glass both side having 12 mm air gap. Stainless steel (SS 304 grade) adjustable friction window stay. 205 x19mm Stainless steel (SS 304 grade) adjustable friction window stay 255 x19mm Stainless steel (SS 304 grade) adjustable friction window stay. 355 x19mm Stainless steel (SS 304 grade) adjustable friction window stay. 510 x19mm Stainless steel (SS 304 grade) adjustable friction window stay. 710 x19mm Masking tape. Aluminium casement window fastener (Anodised AC 15 ) Aluminium casement window fastener (powder coated ). Aluminium casement window fastener (polyester powder coated). Aluminium round shape handle (anodised AC 15) Aluminium round shape handle (powder coated) Aluminium round shape handle (polyester powder coated). Stainless steel screws 25mm x4mm Anodised Aluminium butt hinges 100 x 75 x 4 mm size Stainless steel dash fastener of 8 mm dia and 75 mm long bolt Aluminium Grill Toughened glass 12 mm thickness Structural sealant Spacer tape 6.4 mm thick x 6 mm wide Weather Sealant - Non Staining (600 ml) Weather Sealant - Normal (300 ml) MS Brackets / Aluminium Alloy Brackets Silicon gasket in kg (above 50 g/m) EPDM gasket in kg (above 60 g/m) Anchor Fastner - M10 SS Bolt with washer of sizes for structural glazing / ACP cladding SS Screws of sizes for structural glazing / ACP cladding Protective Tape GI flashing - 1.2 mm Thick 6 mm thick High performance glass 6 mm thick clear heat strengthened glass 6 mm thick clear heat strengthened glass ARMS GS HD- Top Hung - 20" - Type P - Couple Connection Block or vision glass panel Curtain wall striker for vision glass panel Adjustable fastening pawl for vision glass panel Corner drive for vision glass panel Top wedge block for vision glass panel Glass wool of density @ 48 kg / cum with black glass tissue (BGT) SS Screws - #8 x 19 Weather Sealant - DC 789 cartridge Cement Board Baker rod 4 mm thick FR Grade Class B1 ACP sheet 3 mm thick FR Grade Class B1 ACP sheet Fire stop GI / Aluminium Sheet (0.8 mm thick) 4 point façade glass bracket without flat head bolts 2 point façade glass bracket (wall mounted without flat head bolts) 1 point façade glass bracket (wall mounted without flat head bolts) Flate head bolt for brackets of spider glazing 400 mm long fin plate without fastners Stainless steel U Channel of size (50x25x2mm) Non staining water resistant clear silicon 21mm thick clear toughened Laminated glass for fins with holes 4 mm thick FR Grade Class A2 ACP sheet Float glass sheet of nominal thickness 8 mm.(weight not less than 20 kg/sqm). Aluminium Strip 40 mm wide and 2 mm thick Toughened glass 8 mm thickness Toughened glass 10 mm thickness | Metre | 3,171.80 |
| 9.1 | Providing structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required | KG | 107.20 |
| 9.2 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required | KG | 109.60 |
| 9.3 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required | Sqm | 8,166.80 |
| 9.4 | Providing and fixing in position 1mm thick M.S. sheet sliding-shutters with frame and diagonal braces of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junction and corners 25mm dia pulley, 40x40x6mm angle and T-iron guide sufficiently long at the top and bottom respectively, channels & with bolts, nuts, rivets, locking arrangement, stoppers, handles, hold fast including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required | Sqm | 5,617.50 |
| 9.5.1 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as requiredUsing M.S. angels 40x40x6 mm for diagonal braces | Sqm | 4,711.70 |
| 9.5.2 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as requiredUsing flats 30x6mm for diagonal braces and central cross piece | Sqm | 4,486.40 |
| 9.6.1 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required80xl.25mm M.S. laths with 1.25 mm thick top cover | Sqm | 3,669.30 |
| 9.6.2 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required80x1.20 mm M.S. laths with 1.20 mm thick top cover | Sqm | 3,095.50 |
| 9.6.3 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required80x0.90 mm M.S. laths with 0.90 mm thick top cover | Sqm | 2,943.80 |
| 9.7 | Providing and fixing ball bearing for rolling shutters (exceeding 10 sqm area) of approved make complete as required | Each | 629.20 |
| 9.8.1 | Extra for providing & fixing mechanical device chain and crank operation for operating rolling shutters of approved make complete as requiredExceeding 10.00 sqm and upto 16.80 sqm in the area | Sqm | 1,231.30 |
| 9.8.2 | Extra for providing & fixing mechanical device chain and crank operation for operating rolling shutters of approved make complete as requiredExceeding 16.80 sqm in area | Sqm | 1,236.10 |
| 9.9 | Extra for providing & fixing grilled rolling shutters manufactured out of 8 mm dia. M.S. plain bar instead of laths as per design approved by Engineer-in-charge (area of grill to be measured) complete as required | Sqm | 1,173.70 |
| 9.10.1 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primerFixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) | KG | 136.60 |
| 9.10.2 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primerFixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) | KG | 129.80 |
| 9.11 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T- iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-in-Charge | KG | 117.40 |
| 9.12.1 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. completeHot finished welded type tubes | KG | 146.20 |
| 9.12.2 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. completeHot finished seamless type tubes | KG | 161.10 |
| 9.12.3 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. completeElectric resistance or induction butt welded tubes | KG | 143.20 |
| 9.13 | Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete | Each | 192.80 |
| 9.14 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape, including painting the exposed portion as per standard drawing complete as required (provided incase of low ceiling height) | Each | 193.60 |
| 9.15.1 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as requiredIn stringers, treads, landing etc. of stair cases including use of chequered plate wherever required, all complete | KG | 121.80 |
| 9.15.2 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as requiredIn grating, frames, guard bar, railing, brackets, gates and similar works, all complete | KG | 142.30 |
| 9.16.1 | Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as requiredM.S. tube | KG | 148.90 |
| 9.16.2 | Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as requiredE.R.W. tubes | KG | 151.50 |
| 9.16.3 | Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as requiredG.I.pipes | KG | 173.00 |
| 9.17 | Providing and fixing M.S. round holding down bolts with nuts and wahser plates complete as per standard design | KG | 103.90 |
| 9.19 | Providing and fixing M.S. rivets of sizes in position complete as per standard design | KG | 210.40 |
| 9.21.1 | Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge10 x 60 mm | Each | 100.10 |
| 9.21.2 | Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge10 x 80 mm | Each | 107.90 |
| 9.21.3 | Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge10 x 120 mm | Each | 129.50 |
| 9.21.4 | Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge10 x 140 mm | Each | 143.70 |
| 9.21.5 | Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge10 x 160 mm | Each | 174.50 |
| 9.22 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) | KG | 695.80 |
| 9.23.1 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts completeGalvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides | Sqm | 782.60 |
| 9.23.2 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts completeStainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides | Sqm | 1,148.00 |
| 9.24.1 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with4.0 mm thick glass panes | Sqm | 1,326.90 |
| 9.24.2 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with5.5 mm thick glass panes | Sqm | 1,671.50 |
| 9.25 | Extra for providing and fixing steel beading of size 10 x 10 x 1.6 mm (box type), approved shape and section with screws instead of glazing clips and metal sash putty, in steel doors, windows, ventilators and composite units | Metre | 60.90 |
| 9.26 | Providing, fabricating, transporting, assembling and erection in position of Steel members for steel colunms, built up beams using structural tubular sections (round, square or rectangular hollow tubes etc. confirming to IS 4923 / IS 1161, Yield strength 310 MPa as per latest IS Code) to the required profile & shape as called for as per the drawing & specifications and of approved make including the shear connectors /studs and fusion weld to top of horizontal member. This item also includes prepration of shop drawings and their approval, necessary templates, adequate temporary supports, scaffolding & staging, all cutting, grinding, sliding & all labour tools, plants & equipments & operations etc. required to complete the job as per drawing & specification. Every precaution to be taken to prevent rusting of sections. This item also includes all test on materials & welded fabricated parts as per specification and direction of Engineer - in - Charge. Temporary bolts & nuts ( grade EN 8 ) to be used during assembling & shall be removed before site erection. All site erection bolts shall be HSFG type only. The item to include cost of sand blasting on materials, application of primer and epoxy paint in internal & external in fabrication shop & final painting on site including all touch up works after erection as per technical specification. Scope of work includes: i) Design & fabrication of any additional temporary structure including all type of lifting brackets, supporting brackets,which will be required for transportion & erection in position / launching of fabrication part or complete element in position. ii) Making provision & arrangement for required opening / inserts for fixing lights fixtures & funning cable conduits. iii) All incidentials labour, equipement & plants required to execute & complete the job from fabrication to erection at final position as per drawing, specification & direction of Engineer - in - Charge. iv) Cleaning & removing of all spoil, temporary arrangementa for casting of deck slab/roofing. v) All safety measures required to execute & complete the work. vi) Procurement of all materials from approved manufactures & fabrication. Complete methodology for structural steel work, Name of workshop for fabrication works, Testing facilities & erection procedures etc.to be intimated for approval of Engineer - in - Charge. vii) The provision of temporary bearing / sand jacks for supporting steel members during erection. viii) Provision of stability during erection against wind load or any other type of loading on structural steel members during erection. ix) Measurement shall be only for structural steel which is erected & is part of permanent structure & paid as per approved shop drawings. All wastages, temporary works, Jigs, temporary assembly bolts etc. are deemed to be included in rates. No allowence or increse in weight for welding, nuts & bolts etc will be applicable | KG | 161.40 |
| 9.27 | Providing, fabricating, transporting, assembling and erection in position of Steel members for steel colunms, built up beams using structural tubular sections (confirming to IS 2062 -1999 grade B Fe 410, normalized control cooled, yield strength + 250 MPa as per latest IS Code) to the required profile & shape as called for as per the drawing & specifications and of approved make including the shear connectors /studs and fusion weld to top of horizontal member. This item also includes prepration of shop drawings and their approval, necessary templates, adequate temporary supports, scaffolding & staging, all cutting, grinding, sliding & all labour tools, plants & equipments & operations etc. required to complete the job as per drawing & specification. Every precaution to be taken to prevent rusting of sections. This item also includes all test on materials & welded fabricated parts as per specification and direction of Engineer - in - Charge. Temporary bolts & nuts ( grade EN 8 ) to be used during assembling & shall be removed before site erection. All site erection bolts shall be HSFG type only. The item to include cost of sand blasting on materials, application of primer and epoxy paint in internal & external in fabrication shop & final painting on site including all touch up works after erection as per technical specification. Scope of work includes: i) Design & fabrication of any additional temporary structure including all type of lifting brackets, supporting brackets,which will be required for transportion & erection in position / launching of fabrication part or complete element in position. ii) Making provision & arrangement for required opening / inserts for fixing lights fixtures & funning cable conduits. iii) All incidentials labour, equipement & plants required to execute & complete the job from fabrication to erection at final position as per drawing, specification & direction of Engineer - in - Charge. iv) Cleaning & removing of all spoil, temporary arrangementa for casting of deck slab/roofing. v) All safety measures required to execute & complete the work. vi) Procurement of all materials from approved manufactures & fabrication. Complete methodology for structural steel work, Name of workshop for fabrication works, Testing facilities & erection procedures etc.to be intimated for approval of Engineer - in - Charge. vii) The provision of temporary bearing / sand jacks for supporting steel members during erection. viii) Provision of stability during erection against wind load or any other type of loading on structural steel members during erection. ix) Measurement shall be only for structural steel which is erected & is part of permanent structure & paid as per approved shop drawings. All wastages, temporary works, Jigs, temporary assembly bolts etc. are deemed to be included in rates. No allowence or increse in weight for welding, nuts & bolts etc will be applicable | KG | 142.70 |
| 9.28 | Providing testing & tigthtening of high strength friction grip bolts (HSFG bolts ) of class / grade EN 8 up to proof load as per IS 4000, including required threading, using automatic calibrated torque wrench at all locations & all heights and their compitable nuts & washers all complete required to execute the job. All HSFG bolts, nuts & washers confirming to IS 1367, IS 6610 & IS 4000 shall be used. The measurement shall be made for complete assembly of bolt, nut & compitable washers used in permanent works. Hire charges of Concrete Mixer 0.25 to 0.40 cum with hooper Machine for rubbing of floors Beldar Bhisti/ Waterman Blaksmith 2nd class Carpenter 1st class Carpenter 2nd class Coolie Driver (for Road Roller, Concrete Mixer, Truck etc.) Fitter (grade 1) Foreman Mason (average) Mason (brick layer) 1st class Mason (brick layer) 2nd class Mason (for ornamental stone work) 1st class Mate Mistry Skilled Beldar (for floor rubbing etc.) Fine sand (selected quarry) Portland Cement White Cement Marble chips large size above 4 mm White & black Marble dust/ powder Marble chips up to 4mm and downsize White & black Well burnt brick aggregate (Single size): 20 mm nominal size Well burnt brick aggregate (Single size): 10mm/ 12mm / 12.5mm nominal size Stone Aggregate (Single size): 20 mm nominal size Stone Aggregate (Single size): 12 / 12.5 mm nominal size Stone Aggregate (Single size): 10 mm nominal size Stone Aggregate (Single size): 06 mm nominal size Bitumen penetration 80/25 (blown type) of approved quality Flats up to 10 mm in thickness Structural steel such as tees, angles channels and R.S. joists Brick (1st class) White marble Raj Nagar plain 18 mm thick (slab area 0.10 sqm to 0.50 sqm) White marble Raj Nagar plain 14 mm thick (slab area 0.10 sqm to 0.50 sqm) Oxidised mild steel screws 50 mm Stainless steel screws 50 mm Second class teak wood in planks (local) Stainless steel screws 30 mm Welding by electric plant DELETED 8 mm thick marble tiles (polished) Raj Nagar Acid and alkali resistant tiles 300x300 mm size, 10 mm thick Acid proof cement Agaria white marble slab plain 18 mm thick Aluminium Strip 40 mm wide and 2 mm thick Black colour dark shade pigment Black Zebra marble slab plain 18mm thick DELETED DELETED DELETED Precast chequered cement concrete tiles 18 mm thick (dark shade) Chequered terrazzo tiles 22 mm thick (light shade) Glass strip 40 mm wide 4 mm thick Green or blue medium shade pigment Hardening Compound High polymer modified quickset tile adhesive Kota stone slab 20 mm to 25 mm thick (semi-polished) Pink marble slab plain 18mm thick Precast terrazzo tiles 22 mm thick (light shade) DELETED DELETED Red, chocolate, orange, buff or yellow (red oxide of iron) light shade pigment Udaipur green marble slab plain 18mm thick DELETED DELETED DELETED DELETED White marble slab Makrana second quality plain veined 18 mm thick White marble slab Makrana second quality plain veined 14 mm thick Agaria white marble slab plain 14 mm thick Black Zebra marble slab plain 14mm thick Udaipur green marble slab plain 14mm thick Pink marble slab plain 14mm thick DELETED Epoxy grout Border tiles Ceramic Tiles Pieces for Crazy Flooring Synthetic polyster triangular fibre of length 12 mm, effective dia. 10-40 microns and specific gravity of 1.34 to 1.40 White marble rajnagar plain stone pieces for crazy flooring Tile fixing chemical adhesive Glass mossaic tiles (20 mm x 20 mm x 4 mm) Cement polymer Grout Compound Acid for cleaning tiles 500x500x40 mm thick Turf paver Bamboo wood Tile Flooring 14mm thick of minimum size 1800mm x 130mm Bamboo wood Quarter Round 18mm thick of size 1900mm x 18mm Bamboo wood door reducer 14mm thick of size 1900mm x 44mm Expanded poly ethylene Foam sheet 4mm thick of Density 40kg/m3 Silicon based Joint Sealant for Tiles Rubber base Adhesive Bamboo wood Skirting 14mm thick of Size 1900mm x 85mm Bamboo wood Tile Wall Cladding 10mm thick, minimum 1800 mm length and minimum 100 mm wide Bamboo wood T-mold 14mm thick of size 1900mm x 44mm Bamboo wood Threshold 14mm thick of size 1900mm x 44mm Expanded poly ethylene Foam sheet 1mm thick of Density 40kg/m3 Laminated wooden plank for Flooring 8mm thick of minimum size 1202mm x 192mm: AC3 Grade Laminated wooden plank for Flooring 8mm thick of minimum size 1202mm x 192mm: AC4 Grade Laminated wood T-profile 15mm thick of size 2286mm x 45mm Laminated wood door reducer 12mm thick of size 2286mm x 45mm Laminated wooden Skirting 12mm thick of Size 2286mm x 60mm DELETED DELETED DELETED DELETED DELETED Tactiles of standardized designs conforming to RNIB (The Royal National Institute for the Blind, UK), DETR (Department of the Environment, Transport and the Regions, UK) & ADA (Americans with Disabilities Act, USA) of size 300 x 300 mm in floors, (thickness to be specified by the manufacturer) specially designed to assist the visually impaired - “foot braille”, with water absorption less than 0.5% Readymade vitrified step (riser) tiles of size 1200 x 600 mm (15mm thickness), in all shades and designs conforming to IS: 4457: 2007 Readymade vitrified step (thread) tiles of size 1200 x 300 mm (15mm thickness double bull nosing), in all shades and designs conforming to IS: 4457: 2007 1st class quality ceramic glazed Wall tiles conforming to IS: 15622 - 2017 (minimum thickness 5mm) of size 450 mm X 300 mm in all colours, shades and design 1st class quality ceramic glazed Wall tiles conforming to IS: 15622 - 2017 (minimum thickness 5mm) of size 600 mm X 300 mm in all colours, shades and design 1st class quality ceramic glazed Wall tiles conforming to IS: 15622 - 2017 (minimum thickness 5mm) of size 600 mm X 250 mm in all colours, shades and design Ceramic (Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles) Ist class quality Floor tiles of size 300 mm x 300 mm in all colours, shades and designs conforming to IS: 15622: 2017 Ceramic (Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles) Ist class quality Floor tiles (Porcelain) of size 600 mm x 600 mm in all colours, shades and designs conforming to IS: 15622: 2018 1st Class quality Floor Tiles / Soluble Salt Strainfree Vitrified tiles (Glossy) of size 600 mm x 600 mm conforming to IS: 15622: 2017 1st Class quality Floor Tiles / Double Charged Strainfree Vitrified tiles (Glossy) of size 600 mm x 600 mm conforming to IS: 15622: 2017 1st Class quality Floor Tiles / Double Charged Strainfree Vitrified tiles (Glossy) of size 800 mm x 800 mm conforming to IS: 15622: 2017 1st Class quality Floor Tiles / Double Charged Strainfree Vitrified tiles (Glossy) of size 1200 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) 600 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) 1200 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) 1800 mm x 800 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid) 600 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid) 1200 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid) 2600mm x 800mm (minmum 15mm. Thick) conforming to IS: 15622: 2017 Glazed Vitrified - full body outdoor tiles of size 300 x 300 mm or more with water absorption less than 0.08% and conforming to IS: 4457-2007 Carriage: Bricks Brick/ Stone aggregate below 40 mm nominal size Timber Steel Cement Stone blocks white & red sand stone & kota stone slab Fine Sand Marble dust and marble chips Tar bitumen Hire charges of Concrete Mixer 0.25 to 0.40 cum with hooper Machine for rubbing of floors Beldar Bhisti/ Waterman Blaksmith 2nd class Carpenter 1st class Carpenter 2nd class Coolie Driver (for Road Roller, Concrete Mixer, Truck etc.) Fitter (grade 1) Foreman Mason (average) Mason (brick layer) 1st class Mason (brick layer) 2nd class Mason (for ornamental stone work) 1st class Mate Mistry Skilled Beldar (for floor rubbing etc.) Fine sand (selected quarry) Portland Cement White Cement Marble chips large size above 4 mm White & black Marble dust/ powder Marble chips up to 4mm and downsize White & black Well burnt brick aggregate (Single size): 20 mm nominal size Well burnt brick aggregate (Single size): 10mm/ 12mm / 12.5mm nominal size Stone Aggregate (Single size): 20 mm nominal size Stone Aggregate (Single size): 12 / 12.5 mm nominal size Stone Aggregate (Single size): 10 mm nominal size Stone Aggregate (Single size): 06 mm nominal size Bitumen penetration 80/25 (blown type) of approved quality Flats up to 10 mm in thickness Structural steel such as tees, angles channels and R.S. joists Brick (1st class) White marble Raj Nagar plain 18 mm thick (slab area 0.10 sqm to 0.50 sqm) White marble Raj Nagar plain 14 mm thick (slab area 0.10 sqm to 0.50 sqm) Oxidised mild steel screws 50 mm Stainless steel screws 50 mm Second class teak wood in planks (local) Stainless steel screws 30 mm Welding by electric plant DELETED 8 mm thick marble tiles (polished) Raj Nagar Acid and alkali resistant tiles 300x300 mm size, 10 mm thick Acid proof cement Agaria white marble slab plain 18 mm thick Aluminium Strip 40 mm wide and 2 mm thick Black colour dark shade pigment Black Zebra marble slab plain 18mm thick DELETED DELETED DELETED Precast chequered cement concrete tiles 18 mm thick (dark shade) Chequered terrazzo tiles 22 mm thick (light shade) Glass strip 40 mm wide 4 mm thick Green or blue medium shade pigment Hardening Compound High polymer modified quickset tile adhesive Kota stone slab 20 mm to 25 mm thick (semi-polished) Pink marble slab plain 18mm thick Precast terrazzo tiles 22 mm thick (light shade) DELETED DELETED Red, chocolate, orange, buff or yellow (red oxide of iron) light shade pigment Udaipur green marble slab plain 18mm thick DELETED DELETED DELETED DELETED White marble slab Makrana second quality plain veined 18 mm thick White marble slab Makrana second quality plain veined 14 mm thick Agaria white marble slab plain 14 mm thick Black Zebra marble slab plain 14mm thick Udaipur green marble slab plain 14mm thick Pink marble slab plain 14mm thick DELETED Epoxy grout Border tiles Ceramic Tiles Pieces for Crazy Flooring Synthetic polyster triangular fibre of length 12 mm, effective dia. 10-40 microns and specific gravity of 1.34 to 1.40 White marble rajnagar plain stone pieces for crazy flooring Tile fixing chemical adhesive Glass mossaic tiles (20 mm x 20 mm x 4 mm) Cement polymer Grout Compound Acid for cleaning tiles 500x500x40 mm thick Turf paver Bamboo wood Tile Flooring 14mm thick of minimum size 1800mm x 130mm Bamboo wood Quarter Round 18mm thick of size 1900mm x 18mm Bamboo wood door reducer 14mm thick of size 1900mm x 44mm Expanded poly ethylene Foam sheet 4mm thick of Density 40kg/m3 Silicon based Joint Sealant for Tiles Rubber base Adhesive Bamboo wood Skirting 14mm thick of Size 1900mm x 85mm Bamboo wood Tile Wall Cladding 10mm thick, minimum 1800 mm length and minimum 100 mm wide Bamboo wood T-mold 14mm thick of size 1900mm x 44mm Bamboo wood Threshold 14mm thick of size 1900mm x 44mm Expanded poly ethylene Foam sheet 1mm thick of Density 40kg/m3 Laminated wooden plank for Flooring 8mm thick of minimum size 1202mm x 192mm: AC3 Grade Laminated wooden plank for Flooring 8mm thick of minimum size 1202mm x 192mm: AC4 Grade Laminated wood T-profile 15mm thick of size 2286mm x 45mm Laminated wood door reducer 12mm thick of size 2286mm x 45mm Laminated wooden Skirting 12mm thick of Size 2286mm x 60mm DELETED DELETED DELETED DELETED DELETED Tactiles of standardized designs conforming to RNIB (The Royal National Institute for the Blind, UK), DETR (Department of the Environment, Transport and the Regions, UK) & ADA (Americans with Disabilities Act, USA) of size 300 x 300 mm in floors, (thickness to be specified by the manufacturer) specially designed to assist the visually impaired - “foot braille”, with water absorption less than 0.5% Readymade vitrified step (riser) tiles of size 1200 x 600 mm (15mm thickness), in all shades and designs conforming to IS: 4457: 2007 Readymade vitrified step (thread) tiles of size 1200 x 300 mm (15mm thickness double bull nosing), in all shades and designs conforming to IS: 4457: 2007 1st class quality ceramic glazed Wall tiles conforming to IS: 15622 - 2017 (minimum thickness 5mm) of size 450 mm X 300 mm in all colours, shades and design 1st class quality ceramic glazed Wall tiles conforming to IS: 15622 - 2017 (minimum thickness 5mm) of size 600 mm X 300 mm in all colours, shades and design 1st class quality ceramic glazed Wall tiles conforming to IS: 15622 - 2017 (minimum thickness 5mm) of size 600 mm X 250 mm in all colours, shades and design Ceramic (Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles) Ist class quality Floor tiles of size 300 mm x 300 mm in all colours, shades and designs conforming to IS: 15622: 2017 Ceramic (Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles) Ist class quality Floor tiles (Porcelain) of size 600 mm x 600 mm in all colours, shades and designs conforming to IS: 15622: 2018 1st Class quality Floor Tiles / Soluble Salt Strainfree Vitrified tiles (Glossy) of size 600 mm x 600 mm conforming to IS: 15622: 2017 1st Class quality Floor Tiles / Double Charged Strainfree Vitrified tiles (Glossy) of size 600 mm x 600 mm conforming to IS: 15622: 2017 1st Class quality Floor Tiles / Double Charged Strainfree Vitrified tiles (Glossy) of size 800 mm x 800 mm conforming to IS: 15622: 2017 1st Class quality Floor Tiles / Double Charged Strainfree Vitrified tiles (Glossy) of size 1200 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) 600 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) 1200 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) 1800 mm x 800 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid) 600 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid) 1200 mm x 600 mm conforming to IS: 15622: 2017 Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid) 2600mm x 800mm (minmum 15mm. Thick) conforming to IS: 15622: 2017 Glazed Vitrified - full body outdoor tiles of size 300 x 300 mm or more with water absorption less than 0.08% and conforming to IS: 4457-2007 Carriage: Bricks Brick/ Stone aggregate below 40 mm nominal size Timber Steel Cement Stone blocks white & red sand stone & kota stone slab Fine Sand Marble dust and marble chips Tar bitumen Machine for rubbing of floors Bandhani Beldar Bhisti/Waterman Blacksmith 1st class Blacksmith 2nd class Carpenter (average) Carpenter 1st class Carpenter 2nd class Coolie/ Helper / Khalashi Fitter (grade 1) Foreman Mason (average) Mason (brick layer) 1st class Mason (brick layer) 2nd class Mason (for plaster of paris work) 1st class Mate Mistry Painter Skilled Beldar (for floor rubbing etc.) Carriage: A.C.sheet and accessories Brick tiles Brick/ Stone aggregate below 40 mm nominal size Cement Fine Sand G.I.sheet and accessories Plaster of paris Steel Tar / Bitumen Timber Flame retardant face insulating board: 12 mm thick Sand (Fine): Local quarry Sand (Fine): Selected quarry Kerosene oil Cement (Portland) Cement (White) Stone Aggregate (Single size): 20 mm nominal size Stone Aggregate (Single size): 10 mm nominal size Paving bitumen Grade VG-10 of approved quality Water proofing materials Flats up to 10 mm in thickness Galvanised steel bolts & nuts 10 mm dia and 125 mm long round head with slots Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots Mild steel bolts 6 mm dia and 25 mm long with hexagonal head Non - Asbestos multi purpose fibre cement board 6mm thick. Rawl plug 50 mm (designation 10 no.) Wire nails Bitumen hot sealing compound: Grade A Flat pressed 3 layer particle board (medium density) Grade I:12 mm thick Bright finished or black enameled mild steel screws 40 mm Oxidised mild steel screws 40 mm Dash fastener/ Chemical fastener All drive screws ( for gypsum board) Primer (for gypsum board) Other wood in planks (Jam, Garjan, Chamal) Local teak wood in planks Red, chocolate, orange, buff or yellow (red oxide of iron) light shade pigment 12 thick particle board ceiling tile 400G virgin polythene sheet 3 mm thick translucent white acrylic plastic sheet Adjustment clip 85x30x0.8 mm Bitumen washer Dash fastener 6 mm dia 50 mm long Expanded polystyrene type - SE 50 mm thick Expanded polystyrene type N- Normal 50 mm thick Flame retardant face insulating board: 12 mm thick G.I. Limpet washer G.I. plain washer for seam bolts Galvanised steel corrugated sheets Galvanised steel J or L hooks 8 mm dia Galvanised steel plain sheets Hanger rod 4 mm thick Galvanised Steel Intermediate cross T section 24x25x0.33 mm (0.6 mtrs) Galvanised Steel Intermediate cross T section 24x25x0.33 mm (1.2 mtrs) Joint filler Joint finisher Joint tape roll Galvanised Steel Main T ceiling sections 24x38x0.33 mm (3 metre long) Natural colour insulating board: 12 mm thick Galvanised Steel Perimeter wall angle 24x24x0.40 mm (3 metre long) Plain ceiling tiles (BWP type phenol formaldehyde synthetic resin bonded) (600x600x12 mm) Hard wood Plug Polyvinyl chloride sheet 400 micron thick Pre-painted Galvalume sheet 0.40 mm Pre-painted Galvalume sheet 0.45 mm Pre-painted Galvalume sheet 0.50 mm Pre-painted Galvalume sheet 0.60 mm Pre-painted Galvalume sheet 0.80 mm Pre-painted Galvalume sheet plain ridges/ Valley/ Gutter/Flashing 0.45mm thick Pre-painted Galvalume sheet plain ridges/ Valley/Gutter/Flashing 0.4mm thick Pre-painted Galvalume sheet plain ridges/ Valley/Gutter/Flashing 0.5mm thick Pre-painted Galvalume sheet plain ridges/ Valley/Gutter/Flashing 0.6mm thick Pre-painted Galvalume sheet plain ridges/ Valley/Gutter/Flashing 0.8mm thick Pre-coated galvanised iron profile sheet 0.50 mm TCT Pre-coated galvanised steel plain ridges/ Valley/Gutter/Flashing 0.5mm thick Pressed clay tiles Resin Bonded Glass wool 16 kg/m³ 50 mm thick Resin Bonded Glass wool 24 kg/m³ 50 mm thick Roofing paint for iron sheets in red colour Seam bolts and nuts 6 mm dia and 25 mm long Galvanised steel Soffit cleat (Size 27x37x25x1.60 mm) Standard quality hard board sheet 3 mm thick Standard quality hard board sheet 4.5 mm thick o u-PVC bend 87.5 110 mm bend u-PVC bend 87.5 o 75 mm bend u-PVC coupler for UPVC drainage pipes 110 mm u-PVC coupler for UPVC drainage pipes 75 mm u-PVC pipe clip 110 mm bend u-PVC pipe clip 75 mm bend u-PVC pipes (working pressure 4 kg / cm2) Rubber (Seal) Ring 110 mm dia. u-PVC pipes (working pressure 4 kg / cm2) Rubber (Seal) Ring 75 mm dia. u-PVC pipes (working pressure 4 kg / cm2) Single socketed pipe 110 mm dia. u-PVC pipes (working pressure 4 kg / cm2) Single socketed pipe 75 mm dia. u-PVC plain shoe 110 mm bend u-PVC plain shoe 75 mm bend u-PVC pushfit coupler (single) 110 mm thick u-PVC pushfit coupler (single) 75 mm thick u-PVC single equal Tee (with door) 110x110x110 mm u-PVC single equal Tee (with door) 75x75x75 mm u-PVC single equal Tee (without door) 110x110x110 mm u-PVC single equal Tee (without door) 75x75x75 mm UV stabilised 2 mm thick corrugated FRP sheet UV stabilised 2 mm thick plain FRP sheet White face insulating board:12 mm thick M S Wire mesh (rabbit) Resin Bonded Rockwool 48 kg/m3 High Albedo paint Galvanised Steel ceiling sections 80x26x0.5 mm Galvanised Steel Perimeter channel 20x27x30x0.50 mm Galvanised Steel Intermediate channel 15x45x15x0.90 mm Galvanised Steel angle hanger (ceiling angle: 25x10x0.50 mm Galvanised Steel connecting clips (2.64 mm dia and 230 mm long GI wire) Galvanised Steel soffit cleat (Size 27x37x25x0.60 mm) 12.5 mm thick tapered edge gypsum plain borad Deleted Deleted 12.5 mm thick tapered edge gypsum fire resistant board 12.5 mm thick tapered edge gypsum moisture resistant board 12.5 mm thick Fully Perforated Gypsum Plaster Board GI Metal Tile Lay-in Plain Tegular edge global white color tiles of Size 595x595mm and 0.5 mm thick GI Metal Tile Lay-in Perforated Tegular edge global white color tiles of Size 595x595mm and 0.5 mm thick PVC Laminated Gypsum Tiles (Square edge) of Size 595x595 mm and 12.5 mm thick Gypsum Tiles Fully Perforated Square edge of Size 595x595 mm and 12.5 mm thick Calcium Silicate tegular edged celling tiles 595x595 mm and 15 mm thick 8mm thick Calcium silicate perforated tiles of size 595 x595mm 8 mm thick tapered edge calcium silicate board 15 mm thick, light weight, integral densified micro look edged,false ceiling tiles of size 595x595 mm. Galavanised MS hanger rod 6 mm dia MS fully threaded up to 1000 mm length Galavanised MS L-shape level adjuster of size 85x25x2 mm Galavanised MS 8 mm outer diameter M-6 dash fastener 50mm long 40 mm long S.S screws with plastic rawl plugs Powder coated steel section main-T ceiling sections 15x42x0.40 mm (3000 mm long) Galvanized mild steel perimeter wall angle 22x19x0.40 mm (3000 mm long) Powder coated Galvanised Iron intermediate cross-T section 15x42x0.40 mm (1200 mm long) Powder coated Galvanized Iron intermediate cross-T section 15x42x0.40mm (600 mm long ) 15 mm thick, light weight, integral densified micro look edged,false ceiling tiles of size 595x595 mm. Galvanized iron main-T ceiling sections 30x25x0.30 mm (3000 mm long) Galvanized iron intermediate crossT section 25x25x0.30 mm (1200 mm long) Galvanized iron intermediate crossT section 25x25x0.30 mm (600 mm long) 12 mm thick micro tegular edged semi perforated GFRG (Glass Fibre Reinforced Gypsum) false celing tiles of Size 595x 595 mm 12 mm thick micro tegular edged fully perforated GFRG (Glass Fibre Reinforced Gypsum) false celing tiles of Size 595x 595 mm With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6) 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) Mineral fibre beveled tegular edged ceiling tiles 595x595 mm, 16 mm thick with bioblock, confirming to ISO 5 (class 100) specifications Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement corrugated sheet 6 mm thick Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement close fitting adjustable ridge Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement corrugate serrated adjustable ridge Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement plain wing adjustable ridge Fibre (high impact poly propelene reinforced) cement unserrated adjustable ridge for hips Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement corrugated apron piece Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement eaves filler piece Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement north light curves Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement ventilator curves Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement barge boards boards 6 mm thick Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement ridge finial Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement special north light curves Fibre reinforced by organic fibres and/or inorganic synthetic fibres cement S type louvers G.I. plain washer thick G.I. plain washer thin Galvanised steel bolts & nuts 10 mm dia and 27 cm long both sides threaded with 4 galvanised steel nuts Galvanised steel bolts 10 mm dia and 7 cm long with nuts GI Metal Tile Clip in Plain Beveled edge global white colour tiles of size 600x600 mm and 0.5 mm thick GI Metal Tile Clip in Perforated Beveled edge global white colour tiles of size 600x600 mm and 0.5 mm thick Spring T-section 24x34x0.45 mm (3.00 meter long) Wall angle section 20x30x20x0.50 mm (3.00 meter long) Main C Carrier Size 10x38x10x0.70 mm (3.00 meter long) Spring T-connector C Carrier Connector C Suspension Clip Wire Coupling Clip Hanger rod 4 mm thick Adjustment clip 85x30x0.8 mm Soffit cleat (Size 27x37x25x1.60 mm) Precast heat resistant terrace tiles (size 300x300 mm) and 20 mm thick PU Primer 40 mm (average) PU spray having 40-45 kg/m3 density GI wire netting 3/4" x 24 G 400 G polythene sheet Aluminium troughed profile sheet 0.56mm thick with center to center pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000mm Aluminium troughed profile sheet 0.71mm thick with center to center pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000mm Aluminium troughed profile sheet 0.91mm thick with center to center pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000mm Aluminium profile sheet 0.56mm thick with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm Aluminium profile sheet 0.71mm thick with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm Aluminium profile sheet 0.91mm thick with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm Aluminium Circular(sinusoidal) profile sheet 0.56mm thick with center to center pitch of 75 mm, depth of 19 mm, overall profile width 1250mm,cover width 1150mm Aluminium Circular(sinusoidal) profile sheet 0.71mm thick with center to center pitch of 75 mm, depth of 19 mm, overall profile width 1250mm,cover width 1150mm Aluminium Circular(sinusoidal) profile sheet 0.91mm thick with center to center pitch of 75 mm, depth of 19 mm, overall profile width 1250mm,cover width 1150mm Stainless steel self tapping screw of 6x50mm with SS hex cap and 3mm thick EPDM seal Precoated Aluminium troughed profile sheet 0.56mm thcik with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm Precoated Aluminium troughed profile sheet 0.71mm thick with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm Precoated Aluminium troughed profile sheet 0.91mm thick with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm Aluminium color coated profile sheet 0.56mm thick with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm Aluminium color coated profile sheet 0.71mm thick with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm Aluminium color coated profile sheet 0.91mm thick ith center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm Aluminium profile sheet 0.56mm thick with center to center pitch of 177.5 mm, depth of 28.5 mm, 987mm overall profile width, cover width 900mm Aluminium profile sheet 0.71mm thick with center to center pitch of 177.5 mm, depth of 28.5 mm, 987mm overall profile width, cover width 900mm Precoated/Mill finish Aluminium plain ridges 0.71 mm TCT/plain and 500- 600 mm wide Precoated/Mill finish Aluminium flashings/ aprons 0.50mm TCT/plain and wide upto 600 mm Precoated/Mill finish Aluminium plain north light cuves Precoated/mill finish aluminium Barge board (Upto 200 mm) Precoated/Mill finish Aluminium crimp curve Precoated/Mill finish Aluminium gutter EPDM washer Stainless steel bolts & nuts 10 mm dia and 125 mm long round head with slots Wooden screws with plastic rawl plugs 35x8 mm Red oxide Zinc chromate primer Plaster of Paris Dash hold fastener 12.5 mm dia, 50 mm long with 6 mm dia bolt Aluminium strip 25 mm x 1.4 mm PTMT grating 100/110 mm dia. PTMT grating 75 mm dia. ROOFING Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete as per direction of Engineer-in-charge. 0.80mm thick with zinc coating not less than 275gm/m2 0.63mm thick with zinc coating not less than 275gm/m2 Extra for straight cutting in C.G.S. sheet roofing for making opening of area exceeding 40 sq. decimeter for chimney stacks, sky light etc.: 0.80mm thick 0.63mm thick Extra for circular cutting in C.G.S. sheet roofing for making opening of area exceeding 40 square decimeter 0.80mm thick 0.63mm thick Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers etc. complete as per direction of Engineer-in- charge. 0.80mm thick with zinc coating not less than 275gm/m2 0.63mm thick with zinc coating not less than 275gm/m2 Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers etc. complete as per direction of Engineer-in-charge: 1.60mm thick with zinc coating not less than 350gm/m2 Providing and fixing of 40 cm over all width in plain, G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts, G.I. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 (1cement: 3 fine sand) etc. complete as per direction of Engineer-in-charge. 1.00mm thick with zinc coating not less than 275gm/m2 Providing and fixing 15 cm wide 45 cm over all semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes etc. complete as per direction of Engineer-in-charge. 0.80mm thick with zinc coating not less than 275gm/m2 0.63mm thick with zinc coating not less than 275gm/m2 Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required etc. complete as per direction of Engineer-in-charge. Extra for straight cutting in reinforced by organic fibres and/or inorganic synthetic fibres cement corrugated, semi corrugated 6 mm thick sheet roofing for making openings of area exceeding 40 square decimeter for chimney stacks, skylights etc. Extra for circular cutting in reinforced by organic fibres and/or inorganic synthetic fibres cement corrugated/ semi corrugated 6 mm thick sheet roofing for making openings of area exceeding 40 square decimeter. Extra for providing and fixing wind ties of 40x 6 mm flat iron section. Providing and fixing ridges and hips in fibre cement reinforced by organic fibres and/or inorganic synthetic fibres roofing with suitable fixing accessories or self drilling fastener and EPDM washer etc. complete as per direction of Engineer-in-charge. Corrugated serrated adjustable ridges Plain wing adjustable ridges Close fitting adjustable ridges Unserrated adjustable hips Providing and fixing fibre cement reinforced by organic fibres and/or inorganic synthetic fibres roofing accessories in all colours with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete as per direction of Engineer-in-charge: Corrugated apron pieces Eave's filler pieces North light curves Ventilator curves Barge boards Ridge finials Special north light curves S type louvers Providing flat iron brackets 50x3mm size with necessary bolts, nuts and washers etc. for fixing G.S. sheets gutters with purlins etc. complete as per direction of Engineer-in-charge. Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of fine sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil etc. complete as per direction of Engineer-in-charge: With residual type petroleum bitumen of grade VG -10 Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement: 4 fine sand) mixed with 2% integral water proofing compound laid over a bed of 20 mm thick cement mortar 1:4 (1 cement: 4 fine sand) and finished neat etc. complete as per direction of Engineer-in-charge. Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 fine sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design and as per direction of Engineer-in-charge: In 75x75 mm deep chase Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 fine sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 fine sand) and a coat of neat cement, rounding the edges and making and finishing the outlet etc. complete as per direction of Engineer-in-charge. Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified and as per direction of Engineer-in-charge. 2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2"or 3"or 6") as specified. 2mm thick flat Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and as per direction of Engineer-in- charge. Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete for Ridges/Valley/Gutter/Flashing of width 600mm etc. complete as per direction of Engineer-in- charge. Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and as per direction of Engineer-in-charge. 0.40mm thickness 0.45mm thickness 0.50mm thickness 0.60mm thickness 0.80mm thickness Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side etc. complete as per direction of Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm: 0.40mm thickness 0.45mm thickness 0.50mm thickness 0.60mm thickness 0.80mm thickness Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete as per direction of Engineer-in-charge. (frame work to be paid separately): 12 mm thick natural colour insulating board 12 mm thick White face insulating board 12 mm thick Flame retardant face insulating board Providing and fixing flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked in ceiling with necessary nails etc. complete as per direction of Engineer-in-charge. (frame work to be paid separately): 12 mm thick Providing and fixing plain Multipurpose Cement board (High Pressure steam cured) as per IS: 14862: 2000 with suitable screws for fibre cement board in ceiling etc. complete as per direction of Engineer-in- charge. (frame work to be paid separately): 6 mm thick cement board Extra for Circular cutting and waste in ceiling with: 2nd class teak wood planks 20 mm thick Natural colour insulating board 12 mm thick White face insulating board: 12 mm thick Flame retardant face insulating board: 12 mm thick Standard quality hard board sheet: 3 mm thick Standard quality hard board sheet: 4.5 mm thick Extra for providing and fixing ceiling to curved surfaces in narrow widths. Providing 10mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level over first class wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame etc. complete as per direction of Engineer-in-charge. (frame work to be paid separately): Flat surfaces Curved surfaces Extra for any sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling. Extra for providing plaster of Paris (Gypsum anhydrous) ceiling above 5 metres height from floor level. Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part I. 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I. 12.5 mm thick tapered edge gypsum moisture resistant board. Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern etc. complete as per direction of Engineer-in-charge. and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60. Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings etc. complete and as per direction of Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing. Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer- in-Charge. Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK. Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm, of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing. Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS: 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/ c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles. Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 mm reveal profile (white/black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction of Engineer-in- Charge. With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles. With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles. Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T- Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T- sections used in false ceiling support system shall be pre- painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per direction of Engineer-in-charge. With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6). With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7). With 16 mm thick beveled tegular mineral fibre Anti- microbial false ceiling tile confirming to ISO 5 (class 100 ) specifications. Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS: 8193 density 24kg/m3, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5mm x 24g wire and mesh, for top most ceiling of building etc. complete as per direction of Engineer-in-charge. Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8193. Density 16kg/m3, 50mm thick, wrapped in 200G Virgin Polythene bags placed over existing false ceiling and held in position by criss-crossing GI wire etc. complete as per direction of Engineer-in-charge. Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m³, 50 mm thick, wrapped in 400G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per direction of Engineer-in-Charge. Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Rockwool conforming to IS: 8183, density 48 kg/ m³, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building etc. complete as per direction of Engineer-in-Charge. Providing and fixing thermal insulation with Resin bonded rock wool conforming to IS: 8183, density 48 kg/m³, 50 mm thick, wrapped in 200 G virgin Polythene bags placed over existing false ceilng and held in position by criss- crossing Gl wire etc. complete as per direction of Engineer-in-charge. Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m³, 50 mm thick, wrapped in 200 G Virgin Polythene Bags fixed to wall with screws, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-in- Charge. Thermal Insulation of roofing with Expanded polystyrene fixed with suitable adhesive to the false ceiling as per direction of Engineer-in-charge: With Type N - Normal 50 mm thick With Type SE - Self Extinguishing type 50 mm thick Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively), VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifications and as approved by Engineer-in-Charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc., washing with water all complete. The contractor shall give guarantee for the perfomance of SRI and also the durabitity of coating, all complete as per direction of Engineer-in-Charge. Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets etc. complete as per direction of Engineer-in-charge. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with: GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation. Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement: 4 fine sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. all complete as per direction of Engineer-in-Charge. Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-45 kg/ cum), over a coat of polyurethane primer applied @ 6-8 sqm per litre, laying 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed 1:2:4 (1 cement: 2 fine sand: 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints with polymerized mastic, all complete as per direction of Engineer-in-Charge. Providing & fixing at all heights, levels and locations Mill finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 0.56 mm, Aluminium troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000mm. 0.71 mm, troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm. 0.91 mm, troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm. 0.56mm Aluminium profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm. 0.71mm Aluminium profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm. 0.91mm Aluminium profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm. 0.56mm Aluminium Circular (sinusoidal) profile with center to center pitch of 75 mm, depth of 19 mm, overall profile width 1250mm, cover width 1150mm. 0.71mm Aluminium Circular (sinusoidal) profile with center to center pitch of 75 mm, depth of 19 mm, overall profile width 1250mm, cover width 1150mm. 0.91mm Aluminium Circular (sinusoidal) profile with center to center pitch of 75 mm, depth of 19 mm, overall profile width 1250mm, cover width 1150mm. Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 0.56 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm. 0.71 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm. 0.91 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm. 0.56mm Aluminium color profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm. 0.71mm Aluminium color coated profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm. 0.91mm Aluminium color coated profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm. 0.56 mm Aluminium profile with center to center pitch of 177.5 mm, depth of 28.5 mm, 987mm overall profile width, cover width 900mm 0.71 mm Aluminium profile with center to center pitch of 177.5 mm, depth of 28.5 mm, 987mm overall profile width, cover width 900mm Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self-drilling/ tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete as per directions of the Engineer-In-Charge. Precoated/mill finish aluminium Ridges plain (500- 600mm) Precoated/mill finish aluminium Flashings/ Aprons (Upto 600 mm) Precoated/mill finish aluminium North light curves Precoated/mill finish aluminium Barge board (Upto 200 mm) Precoated/mill finish aluminium Crimp curve Precoated/mill finish aluminium Gutter (600 mm over all girth) Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge: Single socketed pipe - 75 mm OD Single socketed pipe - 110 mm OD Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type-A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge: Coupler 75 mm 110 mm Single pushfit Coupler 75 mm 110 mm Single equal tee without door 75x75x75 mm 110x110x110mm Single equal tee with door 75x75x75 mm 110x110x110mm Bend 87.5° 75mm 110mm Plain shoe 75mm 110mm Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1: 4 (1cement: 4 fine sand) making good the wall etc. complete as per direction of Engineer-in-charge. 75mm 110mm Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. etc. complete as per direction of Engineer-in-charge. 75mm 100mm Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC rain water pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc. complete as per direction of Engineer-in-charge. 75mm 110mm Hire charges of Spraying machine including electric charges Grinding buffers Beldar Bhisti/ Waterman Coolie/Helper/Khalashi Foreman Mason (average) Mason (brick layer) 1st class Mason (for plaster of paris work) 1st class Mate Painter White Washer Polisher 1st class Polisher 2nd class Sand (fine): Selected quarry Kerosene oil Cement (Portland) Marble chips up to 4mm and downsize White & black Marble dust / powder Stone dust Water proofing materials Red oxide Zinc chromate primer Acrylic distemper 1st quality having VOC content less than 50 gm / litre Acid proof paint (chocolate or black) Acrylic exterior paint Aluminium paint Aluminium primer Ammonium chloride Anticorrosive bituminous paint (black) Black Japan Paint Deleted Coal Tar Colouring material Copper acetate Copper chloride Copper nitrate Crushed stone 2.36 mm to 12.5 mm size Dehradun white lime Dry distemper Dry hydrated lime (factory made) Epoxy paint Fire retardant paint Floor enamel paint in all shades except green Glue Hydrochloric acid Indigo Linseed oil (double boiled) Deleted Oil type wood preservative Ordinary varnish Deleted Plaster of Paris Deleted Premium Acrylic smooth exterior paint Deleted Soft water Spirit Deleted Superior copal varnish Superior spar varnish Synthetic enamel paint in all shades except black or chocolate shade Synthetic enamel paint in black or chocolate shade Textured exterior paint Water proofing cement paint Wax polish (ready made) White lead Whiting Wood filler (Shellac) White cement based putty Deleted Acrylic Exterior Primer Multi Surface Paint Special primer (C.W.) Ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre Ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ litre Water thinnable cement primer on wall surface having VOC content less than 50 grams/litre Silicon and acrylic emulsion Acrylic emulsion, having VOC content less than 50 grams/ litre Premium acrylic emulsion paint of interior grade, having VOC content less than 50 grams/ litre Synthetic enamel paint, having VOC content less than 150 grams/ litre Premixed super white gypsum plaster Synthetic ployster triangular fibre of length 6 mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 White cement based polymer modified self curing compound in powder form Deleted Melamine Polish Santa Lime 100% Premium acrylic dirt resistance, Silicone additives exterior paint Melamine wood sealer Melamine solvent/thinner Sanding cloth 150 mm wide Sand papers of assorted gratings Melamine wood filler putty Dhoti (worm out soft cotton cloth) Carriage: Cement Carriage: Fine Sand Carriage: Water proofing material / White lime/ Whiting / Lime Carriage: Marble dust and marble chips Carriage: Plaster of Paris Carriage: Stone dust Note:- Rates for external plaster are for height upto 10m from ground level in less otherwise stated | KG | 298.70 |
Other chapters in this schedule
- Earth Work (27)
- Mortars (10)
- Cement Concrete (34)
- Reinforced Cement Concrete (60)
- Brick Work (79)
- Cladding Work (38)
- Wood & PVC Work (291)
- Finishing Work (80)
- Repairs to Building (74)
- Dismantling & Demolishing (33)
- Aluminium Work & Structural Glazing (9)
- Water Proofing & Rehabilitation Work (9)
- Sanitary Installations (9)
- Water Supply (315)
- Sewage & Drainage (37)
- Bamboo & Thatch Roofing Work (22)
Pricing steel work against a live tender
Mapping a tender BOQ to the right schedule items, applying the current cost index, and catching where rates have moved since the base edition is slow and easy to get wrong. Arched's estimation engine reads the tender, maps it to the applicable schedule, and flags where the numbers are exposed before submission.
See how estimation works