Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified
- Item number
- 12.47.1
- Analysis basis
- area of
- Priced inputs
- 11
- Derived rate
- ₹1,401.35/ SQM
Under the CPWD Delhi Analysis of Rates 2023 (Civil), item 12.47.1 (Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified 2 mm thick corrugated (2.5” or 4.2” or 6”) or step-down (2” or 3” or 6” ) as specified) is derived from 11 priced inputs for area of and works out to ₹1,401.35 per sqm after water charges, GST, CPOH and cess. The full build-up is below.
- 2x18.09x5.1 = 184.518 sqm.
- G.I.Seam bolts and nuts 60cm centre to
- centre zig-zag i.e. 30cm centre to centre
- straight Breadth is 5.1metre
- No. of bolts in one lap 5.1/0.3 =17 nos.
- 2x26(laps)x17 nos. = 884 nos.
- G.I.,J or L hooks 8mm dia.
- (No. of purlins to be used 5 on either
- side)2x5x27
- (No. of sheets)x23 nos. of bolts in each
- sheet = 810 nos.
- (total of seam and J bolts)
- 884+810= 1694
| Code | Type | Input | Unit | Quantity | Rate (INR) | Amount (INR) |
|---|---|---|---|---|---|---|
| 8668 | MAT | UV stabilised 2 mm thick corrugated FRP sheet | sqm | 240.408 | 588.00 | 1,41,359.90 |
| 9977 | MAT | Carriage of sheet | L.S. | 104 | 2.27 | 236.08 |
| 1022 | MAT | Galvanised steel bolts & nuts 6 mm dia and 25 mmlong round head with slotsGalvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots | 10 Nos | 88.4 | 38.00 | 3,359.20 |
| 1023 | MAT | Galvanised steel J or L hooks 8 mm dia | 10 Nos | 81 | 130.00 | 10,530.00 |
| 1207 | MAT | G.I. Limpet washer | 100 Nos | 16.94 | 21.00 | 355.74 |
| 1208 | MAT | Bitumen washer | 100 Nos | 16.94 | 30.00 | 508.20 |
| 9977 | MAT | Carriage of bolts and washers | L.S. | 26.91 | 2.27 | 61.09 |
| 9999 | MAT | Sundries | L.S. | 53.82 | 2.27 | 122.17 |
| 0130 | LAB | Mistry | day | 1.3 | 897.00 | 1,166.10 |
| 0112 | LAB | Carpenter 2nd class | day | 15.5 | 816.00 | 12,648.00 |
| 0114 | LAB | Beldar | day | 15.5 | 736.00 | 11,408.00 |
- TOTAL
- 1,81,754.48
- Add 1 % Water charges on “W”
- +1,817.54
- TOTAL
- 1,83,572.02
- Add GST on “X” (multiplying factor 0.2127)
- +39,045.77
- TOTAL
- 2,22,617.79
- Add 15% CPOH on “Y”
- +33,392.67
- TOTAL
- 2,56,010.46
- Add Cess @ 1% on “Z”
- +2,560.10
- Cost of 184.518 Sqm.
- 2,58,570.56
- Cost of 1 Sqm.
- 1,401.33
- SAY
- ₹1,401.35
- PUBLISHED BY
- Central Public Works Department (CPWD)
- EDITION
- DAR 2023 · Delhi
- EFFECTIVE
- 2023-09-14Both volumes are dated 14 September 2023 on their title pages.
- RETRIEVED
- 2026-09-08
- GST
- 18%, added in each item's build-up
- PRINTED PAGE
- 909
From the CPWD Delhi Analysis of Rates 2023 (Civil), Volumes I & II, printed page 909. For reference only. CPWD amends rates through correction slips between editions, so verify against the official source before pricing a bid.
Use this rate in a live estimate
This is the CPWD base analysis. A real estimate adjusts it for the project's inputs and the current cost index, then maps it to the tender's BOQ. We can do this for you: send the tender and we return a priced BOQ on the applicable schedule, with rate build-ups and an engineer's sign-off.